Your cart is empty.
Your cart is empty.Product Description
PLEASE NOTE: For WAYNE DALTON doors ONLY!!!
PLEASE NOTE: For WAYNE DALTON doors ONLY!!!
The Bottom Heavy Duty Weather Seal Door. Part number: 154448.
Bottom Seal is used for Wayne-Dalton Models
TS125, TS150, 8300, 5150, 9100, old 6100, 9500, 9600, 9605, 9700, 9800, 5140, 5145, 9400, 9405, 451, 216, 220,464, 8650, 8000, 8100, 8200.
For Wayne Dalton 8000 and 9000 series foam core doors ,Fits models TG, TW, 2411, 2415, TS-125 and others.
Overhead Door Models: 70/180, and 980 and 300 series.
This is a round bead type seal designed to fit into a round track.
Product is made of vinyl and is black in color,3-1/4” overall width.
Can be Ordered 2+ inches Longer Than Actual Length and Can be Easily Cut to Any Length
Installation Steps:
Product installs easily with two people.
One guide’s seal into track and pulls, the other feeds the seal.
It is helpful to completely clean the track after removing old seal.
Apply lubricant to track to ease installation process.
Sam
2025-08-29 17:34:35
This was a perfect fit for my Delden garage door. I sprayed the old gasket down with some silicone spray lube along the tracks and I was able to slide it out pretty easily. It also made installing the new seal quite a bit easier. This new seal does a much better job at closing up the gaps along the bottom of the door. It had a couple feet of extra length, I was able to trim it using scissors.This can be installed with one person but easier if you have one person to feed the gasket while someone else pulls it in.
Andrew Parchinski
2025-08-21 13:51:59
Perfect fit and seems to be made well. I expect a decent life span from this seal. Install wasn’t that bad either.
Tri-State Bob
2025-07-14 13:56:49
Was worried I picked the right one.But with all the small dimensions shown in the pictures on the site.That helped me figure out the correct weather stripping.Thanks for showing all details on the site.~ Tri-State Bob
Lee
2025-05-23 12:42:39
My review on the "product" is that it arrived promptly, as described, and appears to be of good quality.My problem was the garage door metal track that holds the rubber in place, NOT the rubber seal. There are two metal grooves on the bottom of the door. One groove was fine and the edge of the seal would slide into and down the track with ease. The other track was either damaged or manufactured improperly because the seal edge would not go in smoothly. I tried both ends of the track - same problem. It was a struggle to do it by myself, but I got the rubber seal installed on the door. It looks much better than the old "hard" piece and I think it will stop water/debris.
Customer
2025-05-11 16:11:15
I have lived in my house 12 years and never really noticed how bad my garage door seal was. It could be the original from 1997. Well my door is old and I could not find a part number or manual to help figure out what to replace it with. I have a Wayne Dalton Thermowayne 36 and I cut some of the old seal off so I could figure out which style of seal to order. I ordered this one and it looked pretty much the same. I just got it an hour ago. I walked out to my old and dirty garage door. I ripped out the old one like an impatient child. I hit the channel with a rusty wire brush really quick and then stuck the straw from my WD40 into each channel and slid the straw across my 16 foot door. I used a screwdriver to widen the ends of each channel a bit. I dipped my vinyl glove in soap and started to feed the new 18 foot seal into the channel. I did it in about 10 minutes. I left about 1.5 inches of overhang on each side since some people said the seal shrank a bit. I have open and closed the door a few times and it works great. No light coming through to the inside anymore. Once it shrinks a bit I will use nice grips to pinch the ends of the channel tight again. Hope this helps others that have an old Wayne Dalton door that has a few dents and dings but does the job and just needs a new seal.
Char
2025-01-23 12:34:01
This was easy to install according to my husband, seems to do the job as he hasn’t heard back from the customer
Mark Twain
2024-12-18 14:54:45
This was a pain to install. Two person job. Product is very high quality and same or better than original Wayne Dalton.
Shawn Morris
2024-12-17 17:00:31
The seal is not very pliable in the cold weather
Wilson
2024-12-15 11:29:32
This was the perfect seal for my garage door. The tabs on the sides mated with my door perfectly, but double check on your door. It needed a little WD-40 to slide in and I had to cut it to fit the length of my door. Job done.
Customer
2024-11-29 17:59:41
Did replacement on my garage gate. Tshape, perfect fits, fast shipping.
Recommended Products