Shopping Cart

Your cart is empty.

Your cart is empty.

GoolRC Flysky FGr4D Receiver, 2.4GHz 4 Channels AFHDS 3 Receiver Built-in Dual Antenna PWM/PPM/i-BUS2/S.Bus/i-Bus Output Compatible with Flysky Noble NB4 PL18 EL18 RC Transmitter for RC Car Boat

4.9 (2) Write Review
Free shipping on orders over $29.99

$41.95

$ 20 .99 $20.99

In Stock
  • 4 Channels AFHDS 3 Receiver: The FGr4D is a 4-channel two-way receiver based on AFHDS3 (Third Generation Automatic Frequency Hopping Digital System) protocol.
  • Compatible and Application: 2.4GHz 4 channel receiver is compatible with All Transmitters with AFHDS3 Protocol, such as flysky Noble NB4/Noble NB4 Pro/EL18/PL18/PL18 Lite/PL18 EV/PL18 EV Lite RC transmitter, suitable for remote control Car and remote control boat.
  • 4 New Port Function: It supports 4 New port function interfaces (Newport canbe customized with input or output signal types: i-BUS2/S.BUS/i-BUS/PPM).
  • Waterproof: This receiver features dual antennas, PPX6 nano waterproof.
  • Lightweight: Ultra-small size and ultra-lightweight, effectively save space and reduce item's weight-bearing.


Product Description

GoolRC Flysky FGr4D Receiver, 2.4GHz 4CH AFHDS 3 Remote Control Receiver

Flysky FGr4D Receiver

  • The FGr4D is a four-channel two-way receiver based on AFHDS 3 protocol. This receiver features dual antennas, PPX6 nano waterproof, compact and lightweight design. It supports 4 Newport function interfaces. The FGr4D can be used as a PWM converter, adaptable to a model car or model boat
Flysky FGr4D Receiver

Built-in Dual Antennas

  • Wider signal, stable and full coverage.
Flysky FGr4D Receiver

FGr4D VS FGr4S

  • FGr4D receiver control the return communication distance to increase than FGr4S receiver.
Flysky FGr4D Receiver

PPX6 Nano Waterproof

  • Resistant to water jets from any direction and can be used with getting wet.
Flysky FGr4D Receiver

Durable Metal Pin Heade

  • Gold-plated pin header to improve corrosion resistance and extend service life.
Flysky FGr4D Receiver

Compatible and Application

  • 2.4GHz 4 channel receiver is compatible with All Transmitters with AFHDS3 Protocol, such as flysky Noble NB4/Noble NB4 Pro/EL18/PL18/PL18 Lite/PL18 EV/PL18 EV Lite RC transmitter, suitable for remote control Car and remote control boat. Receiver Size: 30.3*25.8*20mm
Flysky FGr4D Receiver

Receiver Installation

  • The receiver has two built-in antennas. In order to ensure the signal quality and avoid the remote control distance affected, the receiver antenna should be perpendicular to the model body (as shown in the figure) when installing the receiver,
Flysky FGr4D Receiver

  • New Port Function: It supports new port function interfaces (New port canbe customized with input or output signal types: i-BUS2/ i-BUS/PWM/S-BUS//PPM).

Binding

The receiver supports two-way binding and one-way binding, and can be set at the transmitter side. The transmitter will display the information returned from the receiver after the two-way binding is completed.

Follow the steps below to bind in two-way binding:

1. Select Two WAY for RF standard of the transmitter, then put the transmitter in bind mode. 2. The receiver supports two ways to enter bind mode: BIND button binding and BIND button binding after power-on.

• BIND button binding: Press and hold the BIND button of the receiver while powering on the receiver, tthe LED of the receiver should be flashing, indicating that the receiver is in bind mode. Then release the BIND button.

• BIND button binding after power-on: The receiver has not been connected to the transmitter when it is powered on. Press and hold the BIND button for 3 seconds, the LED of the receiver should be flashing, indicating that the receiver is in bind mode. Then release the BIND button.

3. When the LED of the receiver is solid on, the binding process should be finished. The transmitter exits the bind mode automaticlly. 4. Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems arise.

Follow the steps below to bind in one-way binding:

1. Select One WAY for RF standard of the transmitter, then put the transmitter in bind mode. 2. Put the receiver in bind mode ( Refer to the description above for entering bind mode). 3. After the receiver LED becomes slow flashing, then put the transmitter to exit the binding state. At this time, the receiver LED is solid on indicating the binding is successful. 4. Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems arise.

Note: When this receiver is used as a PWM converter, it is necessary to finish configurations at the transmitter side. In this case, if the LED works in Flash-once, ON-once, and OFF-once state, it indicates that no i-BUS2 signal is received; if i-BUS2 signal is received, the LED works in Flash-once and ON-once stat.

Flysky FGr4D Receiver

Receiver Overview

  • PWM Channels: 4, RF: 2.4GHz ISM, 2.4G Protocol: AFHDS3, Maximum Power: <20dBm (e.i.r.p.) (EU), Input Power: 3.5~9V/DC, Working Current: ≤ 50mA/5V, Temperature Range:-10℃ ~ +60℃, Humidity Range: 20%~ 95%, Online Update: Yes
Flysky FGr4D Receiver

Package List

  • Lightweight: Ultra-small size and ultra-lightweight, effectively save space and reduce item's weight-bearing. The package included 1* FGr4D receiver, 1* Cable,1* User Manual, 1* Stickers.

Frank Sell
2025-03-26 11:08:19
Tried several times to bind it to my radio with no success.
Megan
2024-12-04 11:15:13
From the beginning these worked fine, I saw no difference between the “S” version in terms of performance, just the feature differences. Then I noticed the bind button wearing for no reason at all, but it didn’t seem to affect anything. Eventually I needed to swap a receiver from one vehicle to another and the entire bottom of the case pulled apart from the top and broke. This happened a second time with the other “D” version I bought after the receiver stopped working. I have 8 other S versions and they have all been flawless, including removal with the case staying intact. No more “D” receivers for me until they put it in a better case.