Shopping Cart

Your cart is empty.

Your cart is empty.

Hippored easyboot 1 Piece - kit Split cv Boot (80mm)

5.0 (8) Write Review
Free shipping on orders over $29.99

$44.00

$ 22 .99 $22.99

In Stock

About this item

  • 1 piece kit containing: 1 boots size ø80mm or ø90mm; 2 ties; 3gr of glue and 50gr of grease
  • INSTRUCTIONS Use boot 80 for cv-joints with a diameter from 78mm to 89 mm and axleshaft from 24mm to 29mm. Use boot 90 for cv-joints with a diameter from 90mm to 110 mm and axleshaft from 24mm to 29mm.
  • CAUTION due to the special glue that fastens the two sides in less than 30 seconds, make sure to carry out the simple task of fitting the part as quickly as possible and in a comfortable position. Cuffia facile (Easy Boot) fits most axle shafts up to a diameter of about 29 mm, for axle shafts with a bigger diameter (very rare on cars) the boot may not close properly and become unusable.
  • PLEASE NOTE: NEVER use glue that is different from the one provided in the kit.


Product Description

Hippored EasyBoot 80mm - split cv boot wheel side

Easyboot 80mm

PRODUCT DETAILS

EasyBoot is an Italian patent. Unlike classic spare parts it allows you to replace the worn-out axle boot without removing any mechanical part. Made of special, extremely durable rubber CUFFIA FACILE (Easy Boot) is equipped with an innovative male/female opening system and a specific seam for gluing. Thanks to its elasticity and design, it adapts to most CV joints and drive shafts of car manufacturers.

1 piece kit containing:

  • 1 boots size ø 80mm
  • 2 ties
  • 5gr of glue
  • 50gr of grease

INSTRUCTIONS Use easy boot 80mm for cv-joints with diameters from 79 to 89 millimetres and axle shafts from 24 to 29 millimetres.

INSTALLATION INSTRUCTIONS

STEP 1

STEP 1

  • Thoroughly clean the drive shaft and place Easyboot on drive shaft.

STEP 2

STEP 2

  • Fill the groove with the glue supplied.

STEP 3

STEP 3

  • Attach the two parts. Wait 5 minutes for the glue to dry.

STEP 4

STEP 4

  • Remove the old bands and cut the old boot.

STEP 5

STEP 5

  • Place the grease supplied inside EasyBoot.

STEP 6

STEP 6

  • Insert EasyBoot and tighten the bands supplied. And that's it!
EasyBoot

EASYBOOT

Save time, make your life easier!

  • CAUTION due to the special glue that fastens the two sides in less than 30 seconds, make sure to carry out the simple task of fitting the part as quickly as possible and in a comfortable position. Cuffia facile (Easy Boot) fits most axle shafts up to a diameter of about 29/30 mm, for axle shafts with a bigger diameter (very rare on cars) the boot may not close properly and become unusable.
  • PLEASE NOTE: NEVER use glue that is different from the one provided in the kit.

azn customer
2025-08-18 10:08:51
Fits for Jeep Patriot 2011.I replaced it when the outside temperature was cold, but theadhesive worked.The replacement cost for the genuine part is$440 at the Japanese dealer.This item is only $56 including shipping.I will buy it again if other parts break.
L. Tecson
2025-08-15 18:41:30
No need to remove CV Axle to install this new boot. Hope it holds up since its just glue that holds the seams. No vibration so far. I just hope the clamps that came with it is the correct CV boot clamps.
Kristen
2025-07-13 14:09:08
Must dry for hours before stretching took for ever to arrive
achille
2025-05-03 09:21:44
Ottimo prodotto
bardina
2025-02-23 11:02:07
Produits génial, facile à a utiliser, fait économiser de l'argent.
Recensore
2024-12-13 13:17:10
La cuffia si presenta di qualità, installata da una settimana, andando a rifinire il bordo più accentuato e non da nessun problema. Consiglio!
Pag
2024-11-19 12:41:51
BON PRODUIT. Quel dommage que l' épaisseur au niveau de l'encolage frotte à chaque tour de cardan sur le carter moteur.806, soufflet de cardan droit coté boite.
samourai
2024-11-13 18:25:09
Très satisfait utilisé ya longtemps les mêmes modèles mais introuvable en magasin même spécialisé cest pourquoi je suis très content de lavoir trouvé sur AMAZON