Your cart is empty.
Your cart is empty.Product Description
80S Leveling Casters
HOLKIE Industrial Casters
3300 LBS | Total Capacity | 2200 LBS |
0.28” / 7.3 mm | Leveling Height | 0.28” / 7.3 mm |
4.7” / 119 mm | Overall Height | 3.5” / 89 mm |
3300 LBS | Total Capacity | 600 LBS |
0.28” / 7.3 mm | Leveling Height | / |
4.7” / 119 mm | Overall Height | 3.5” / 89 mm |
- 60S Leveling Casters
- 3" Stem Caster
Adam Buchan
2025-08-17 15:51:14
I purchased these casters to install a massive safe that need to be elevated off the floor. They are very sturdy and had no issue moving the safe across the floor and made leveling a snap.
Ezra
2025-07-25 21:10:45
I have these casters on an adjustable frame bed, as the wheel kit from Tempurpedic is made of unobtanium and I was having a hard time moving the king size bed around on the rubber feet. I like these wheels came with 2 sets of threaded stems, 1/2 inch is what i needed for my older setup. Most of the newer adjustable frame beds have 6 legs and m8 fasteners, this one is only 4 sae 1/2" -13 thread bolts. I had the 12 inch legs which are now too high for comfortably getting in and out of bed, I used to keep storage under the bed but no longer need that, so these brought the bed height down to where the frame is 4.5 inch above the floor. This is the perfect height for sitting on the edge of the bed and easily getting in and out in the middle of the night. One feature i am pleased with on these wheels is the leveling feature, which acts to lock the wheel from rolling and it is easy to release if the bed needs to be moved. I had to buy 2 sets of these to work with the 2 bed platforms with 4 casters on each and had to rearrange the outer bed frame rails to be lower. It all worked out beautifully, and less than half the cost of trying to piece together random ebay sets that were over a hundred bucks each and didnt have the locking features, plus I could only find 1 set of 6 inch legs. If i need to I can fab up some extensions to bring the bed back up to its previous height, but i think it will be perfect as it is. There is room for the power adapters, mattress pumps, and even the Chili Pad Dock Pro fits under the foot of the bed with no issues. I also had room enough to store my CPAP UPS under there, though I don't really need a UPS anymore with the newer 24v system, a couple 12 batteries can power that thing all night without an inverter whining. I digress.TL/DR Good wheels, high load capacity, holds a 400 pound man on a 250# bed frame with a 60# mattress and about 10# cooling pad and 25# weighted blanket.
SF Resident
2025-07-01 10:05:00
So these seemed great and well built. It’s nice that they come with two sets of bolts - on double sided with m12 and a us 1/2 in on other side and one just m12 all the way (and with a set of nuts for each). I discovered my application required a much longer rod (bottom of band saw that has a lip) and finding m12 1.75 bolt threaded rods proved a real time suck and not successful! Make sure the included bolt length works in your application…
David
2025-04-28 12:27:33
Installed these on an old radial arm saw that weighs about 1000 pounds, so far they seem to work very well. I can move the saw around by myself, rolls easily. Especially nice that you can lower the pads so it is not always sitting on the wheels and you can level it.
Colin Andersen
2025-03-10 13:44:05
I purchased a Certi-flat welding fixture table that came with locking casters. Unfortunately the wheels can still swivel even locked which causes issues. I found these wheels with 1/2 studs, and they are a perfect replacement. It is like having casters and fixed leveling feet in one, and no more stability issues. Granted, it takes a bit more effort to use over the lock lever on the old casters, but it was expected and well worth the change. And these casters are excellent quality. Highly recommend them.
BJW
2025-02-09 10:02:13
1 caster was stripped and would skip over the gears.
A...gamer
2025-02-03 16:39:35
I was looking forward to installing these wheels on my Powermatic 3520C lathe to make it mobile in my shop.Unfortunately the description said the wheel would fit 12mm and 1/2" threads.My lathe has 1/2" threads for the leveler and these wheels do NOT threads into my lathe.I am returning these wheels for that reason.
John Brandi
2025-01-09 14:39:01
These are a must have for heavy wood working machinery. They were very easy to install and operate on my heavy duty wood lathe.
Recommended Products