Your cart is empty.
Your cart is empty.Product Description
The Compression Router Bit
The compression cutters are designed with both up and down-cut flutes. The top portion of the length of cut, closest to the shank, has a left hand spiral, forcing chips down.
when using the compression bit, you must ensure the first pass is below the upcut portion of the bit, or you will get results similar to just cutting with an upcut bit; Using a ramp in, plunging into the material over a distance instead of all at once, and a lead in, starting outside the design to get to the pass depth, it will ensure that the entire piece is super clean on the top and bottom. Compression bits are designed to cut in a single pass, however, if your machine cannot handle that depth of cut you can cut in multiple passes, as long as that first pass is below the upcut portion of the bit.
DLC COATING
- DLC coating increases lifespan by 5 times
- DLC micro-nano composite coating
- High Hardness
- High Wear Resistance
- Stable Performance
- High Temperature Resistance
- Smooth Chip Removal
Up & Down Cut Milling Cutter
Compression bit is the combination of both upcut and downcut spirals. The bottom of the material will be pulled upwards while the top of the material is pushed downwards thus eliminating the risk of damaging the laminated surfaces, leaving a sharp, clean edge on both sides of your workpiece. Non-stick crumbs, smokeless, and silent during processing, smooth cutting, and fast chip removal.
Suitable Material
For carving/cutting/engraving/milling/slotting/sculpturing in materials like MDF, ABS, PVC, PCB, SMT, CNC, acrylic, nylon, resin, plastics, density board, wood, plywood, hardwood etc. Ideal for three-dimensional sculpture, surface machining, 3D relief sculpturing etc.
Universal Chamfered Round Handle
- Good compatibility, easy to use, tightly clamped without slipping
- Increase the vibration resistance and milling speed of the milling cutter
James Robinson
2025-08-26 13:04:26
This is a great bit for pocketing and for cutting out parts. Can really crank up the feed-rate on the CNC and it cuts smoothly and accurately. Great bit. Will definitely buy again if if anything happens to this one or it starts getting dull. Highly recommend for a cutout bit!
Mitch
2025-08-18 16:40:14
I run these at 18k-20krpm at 100-150ipm in 18mm ply or softwood. Cut quality is adequate in one full depth pass, quite clean if you take a finishing pass at .015 step over. We have a 5x10ft machine with 9kw on the spindle. 18mm Baltic is better at 120ipm roughing, 80ipm finishing.I usually get about 6 full sheets of ply before I change the bit. I have gone longer, but the cost/benefit just isn't there to push it.If your bits are breaking, try running faster. You should get hundreds of feet of cutting life.We use these for shop jigs mostly where finger jointing is used for assembly. The small diameter makes for nicer finger joints without a lot of loss to dogbone corners.
Customer
2025-07-19 16:59:11
These are outstanding both in quality and value. Super clean pockets. These are our go to 6mm bits for our CNC based business. All of Hozlys bits bits we have tried have been shockingly good.
cliff newman
2025-05-28 16:41:56
1/8th compression bits are the best bits to cut parts on a CNC machine. Dont buy the expensive bits, it doesnt make a difference. Just buy cheap bit in big packs. I've cut tens of thousands of products with these things; hardwoods, plywood, MDF, etc.
Mike
2025-05-15 14:25:13
Not sure why they can't make these an inch longer for large spindles and collets. Cut well for a few hours, then started leaving ridges on each depth pass.
Scott
2025-05-09 14:58:54
Have used 1 of them so far and bit is still sharp and making good cuts
kyler pinkley
2025-05-05 18:21:52
Not a fan of the super short shank but these bits are wicked sharp. They’ll cut great and leave a smooth edge. Highly recommend. Got them as backup bits but I’ve been using them regularly.
Akirk
2025-04-09 16:32:29
Do not use these on a CNC machine. The shank is way too short and you will destroy your collet and the bit will snap off from the amount of torque/pressure being exerted onto the bit
Ross Gravelle
2025-04-07 12:04:33
Cut very well
SteNo
2025-03-11 19:09:19
Tagliano che è un piacere. Lavorando legno duro non fanno fatica scaldano pochissimo e non bruciano il legno. Consiglio di avanzare 4/5 mm alla volta. In questo modo ho tagliato una tavola di faggio (legno duro e difficile da lavorare) da 4 cm.
Rev Aotearoa
2025-02-23 10:11:53
Great for what I need
JY
2025-02-01 17:00:14
These are high quality bits. Sharp and long lasting! Compare with regular carbide bits, the edge definitely last a lot longer.
Jack Corrado
2024-12-27 11:54:49
Appena provata. Lavora molto bene e il taglio é pulitissimo
Recommended Products