A few months ago I ordered the Huepar 3D Green Beam Self-Leveling Laser Level 3x360. Really nice unit, but I found out trying to get it to an exact height could be a challenge, the magnet on the laser bracket is very helpful, but you don't always have a magnetic surface. I tried my camera tripod, and that worked, but only for about 5ft in height. I mainly use the laser for shelves, pictures and sometimes need to have it a little higher than my camera tripod will go. Then I saw this Telescoping Pole that can work up to 12 foot. After checking out the photos and info, I decided to give this a try. I must say, it is nice and works great. I will describe the best I can. It came in a nice carry bag, this way you can keep all parts together. All the extension poles are made of aluminum, that makes it lightweight and you don't have to worry about rust. Each pole has standard and metric markings, 1/4 inch and 5mm. When you screw the poles together, the marks line up. The tripod is much like a camera tripod, the legs can be extended and adjusted for uneven surfaces. There is also a screw at the top to tighten the stand to the pole, no need to super tighten it, and a bubble level to see when you have the stand level. The bottom pole has a spring and a foot piece to push down on, this is after you select the correct amount of poles for the height needed and use the length adjustment on the bottom pole. Hold the yellow part of the bottom pole in one hand, and the footstep part in the other hand and give a slight twist to unlock the pole to pull out for adjustment, then slight twist to retighten. I mention these things as there were no instructions included.The part that slides onto the pole to hold the laser has a lever to lock it too the pole, The one slight issue I saw with this is when the lever was out, ready to install on the pole, you either had to stick you finger in the bracket to push back the plastic piece that locks it to the pole or when putting it on the pole, you have to tilt the bracket and catch the plastic piece on the pole first. With it unlocked, it should slide straight down on the pole, but this is not happening on the one I have, they could use a spring to pull that piece back to make it work better, or, once you have the bottom pole in the tripod, then put the next pole thru this bracket from the top, it will slide through with ease. Once you have the bracket on the pole, it has a fine adjust, there is a lock screw on the side, be sure this is loose before turning the adjustment, once adjusted to the height, just slightly tighten the lock screw, DO NOT CRANK IT DOWN. There is a top piece to put on the top pole that will rest on the ceiling, but beware, this will do no good on a lay-in ceiling, and if you are using it on popcorn ceiling, it could knock some of that off, so you may want to put the stand in a doorway instead.Overall, for me, this stand should take care of almost anything you need, it is light, portable, easy to put together. I have seen other poles that did not have the tripod, without a tripod, you would be limited to places you could use a laser.

The telescoping pole works great and nice quality. However the tripod is of poor quality. After just a couple light uses one of the legs of the tripod no longer stays connected to the top collar. Customer service sent a replacement and have not had any problems with the new one. Would recommend this product

As others had said, its definitely a little shaky on some setups and fine tuning a little tough but overall works well

Excellent pole and tripod combination which makes super versatile. Very sturdy, feels high end and more expensive than it is. Good for pretty much any job, in any location and at any height. Height is the key limitation I had using a tripod only prior to this. The only limitation is that all pole sections are the same height and, in some cases, it is impossible to set as it is too short to get to the ceiling but adding one more section makes it too tall. I wish it had one shorter section!... still, I give it 5 stars as the value is excellent.

I got it to work for the first job and it might work for the next. The tripod is wobbly so it takes a lot of time for it to settle down. If you can use the spring foot and go from floor to ceiling it is fairly sturdy, but then why have the tripod? With some clamps and a small board the tripod cross braces can be firmed up and that helps a lot, but why should that be neccessary. If the cross braces had a set screw like the top of the tripod has, it would be much sturdier and no boards and clamps would be needed. Otherwise the pole is well made and sturdy and assembles easily. The laser mount leaves a lot to be desired. The tiny locking set screw is difficult to adjust and the knob for adjusting up and down is too small. Both knobs are so close to my rotary level (Hilti PS-24) that I had trouble adjusting the height. It was so wobbly that if I tried to adjust it up or down, it would wobble so much my laser would shut off (auto level out of range) so I couldn't just adjust it while watching the laser beam. I had to move it up or down a little, wait for the wobbling to stop and the beam to come back on, then repeat until it was close unough to use. That was VERY frustrating. The carrying bag was good, thin material but fine if you don't throw it in the truck with other tools. I had to make a 1/8" spacer to go under the level base to make up for the height of the large thread adapter, otherwise the level sat on just the flange of the adapter and was loose. Like I said, I got the job done I bought it for with some hassle.

This is good value for my laser.The bag is nice for storage.Sturdy.

Für was steht 3,7m Teleskopstange? Bei mir war nur die Halterung ohne Stange drin. Kann so nicht viel damit anfangen. Falls die Stange noch geliefert werden sollte, werde ich die Rezension abändern. So habe ich aber nur ein halbes Produkt. Schade

So far I've used this on a few Job sites. It's pretty good. Quality is ok so far. Fit and finish goes along with its price point. Yes there are higher end stands for sure but this one works well. It Comes with its own travel bag so you don't lose pieces of it tossing it in and out of the truck. Over all so far I like it. Use it when you need it and treat it well it should last quite a while. I've used it with my huapar green laser and it works well. Didn't mount to my Bosch but that's an easy $3 fix with a different screw and it was good to go. Over all I'd buy another one. I like the adjustability of this laser stand it works well at any position and easy to adjust.

VERY GOOD LASER TOOL STAND. LIGHT WEIGHT , BUT STRONG. IT ADJUSTS TO AN UNEVEN FLOOR. AND FITS OUR LASER LIGHT SO WELL. THANKS

I purchased this huepar pole kit a year ago. The lock handle cracked and wouldn’t hold the laser level securely. Contacted the company and found out it had a warranty for I believe 2 years. Super fast response from the manufacturer by email. The issue was resolved very quickly. Dealt with Carina by email. The email process was pretty simple and efficient. They sent a complete new replacement kit. Another really good Amazon seller customer service.