Your cart is empty.
Your cart is empty.Product Description
Dale M. Mazzola
2025-08-13 16:49:43
Great mold a little tough to get out once frozen but long lasting ice.
Daisy22
2025-07-28 10:55:32
Easy to use. Easy to clean with a little soap and water. Easy to fill. And you will always have the proper ice cube for your tumbler.
Mary
2025-07-20 14:45:50
Overall, I like this product. It has a couple of downsides, but does the job it was meant to do.Pros: It works well. The ice "cubes" It makes are thick enough that the water in my Yeti tumbler stays cold for hours even when left closed up in a hot car. I can't say for sure that it would stay cold all day in that situation, as I haven't had occasion to leave it in the car all day, but my water certainly has stayed icy cold when left in the car for 3 to 4 hours in the direct sun.Though It took me a couple of uses to figure out the best way to remove the cylinders from the mold, it is quite easy now. 1 Peel down the outer part of the mold 2 Grab the inner "core" , top and bottom, and squeeze it towards its center, which peels it loose from the inner edge of the circle of ice. 3 Grab hold of the cylinder of ice and slide it right off.The first use, I did notice that my water had a slight flavor of the silicone, even though I had washed the mold before using. However, that disappeared very quickly, So it doesn't seem to be a problem.The hard plastic container that holds the mold while freezing is a very important item, and I'm very glad it was included. I have lots of other things in my freezer and can't always make room for the ice cube tray to sit directly on a shelf where it can be perfectly flat, so having that support is great.Cons:On the first use, there was a slight but noticeable flavor of silicone in my water, as stated above, but It dissipated by the second use, so it was only a temporary problem.While the hard plastic container is extremely helpful, the lid refuses to snap on. Even setting it on the counter, getting one end In place and pressed down, when I try to get the other end of the lid to snap into place, it simply won't. Even holding one end down tight and trying to press the other end into place doesn't work. The lid simply will not go on. It is possible that this is just a random defect with mine, but it is there nonetheless.And finally, although this is not a con but just something to be aware of, do not fill the molds all the way to the top. Water expands when it freezes, as we all know, and when I filled the molds to almost full, I couldn't fit the lid on my tumbler with the ice inside. The first time I used these, I had to run the top one under hot water and melt off a good quarter of an inch of its height. Now, I leave a little more than a quarter of an inch of headspace in each mold when I put water in, and that works just fine.
Melisa Ostrowski
2025-07-03 16:15:24
I bought these silicone ice cube trays because my ice maker broke, and they turned out to be a perfect solution! The molds are ideal for making large, cylinder-shaped ice cubes that fit perfectly in my Stanley 30oz and 40oz tumblers. The design is super convenient, and the lid makes filling and releasing the ice a breeze.Highly recommend to anyone who loves big ice cubes for their cups!
Mish82
2025-06-27 15:23:13
The ice this makes is great for my tumblers but the ices is hard to get out.it ices does keep the drink really cold for a little longer then just filling the cup with ices.If you want a good hand workout this is a good option.
Janet White
2025-06-20 18:09:37
Nice ice try, makes it easier to put ice in your stanley cup or any 40oz cup
Annabellzd
2025-06-07 15:19:19
Our ice maker died in the fridge and there was no way I could go without ice for my Stanley Tumbler and all the pretend water I drink during the day. First world problems- right?!?! Ok- so I am more a coffee by day, wake up a million times in the night, to get a sip of water person- but I like it to be cold. And I also need cold ice water to last when I stay up late to read ACOTAR. The ice machine dying was an excuse for me to overnight ship this and try it out. Like others have said- the lid is hard to fit and useless, unless you decide to use the container separately from the silicone mold. But…it is a silicone mold, so ya kinda need the base container. Don’t totally fill or over fill the three levels. 1 goes at the bottom (I thought they would nest inside themselves and tried to put 3 in first) but my much smarter teen showed me otherwise. Duh on my part. Ok- so a bit tricky to pull out, but not hard- did I just say that- this applies to ice molds only! Put some elbow grease into rolling and pulling the silicone mold back off the level you are working on. Then squeeze together the center numbered part and push it down as you pull from the bottom and then you should be able to pull up on the ice ring, to get if off (oof- not sure how else to explain that…can you tell I am reading ACOTAR?). Yes- your fingers are going to freeze. Take breaks in between layers if needed- don’t get frost bite- not fun and makes it hard to fly. BUT…it is worth it, they stack great in the 40oz and stay cold for over 24 hrs. And it looks cool when you drop them in. Just be cautious, level 1, when it clinks into the bottom, can be loud. My dogs think it warrants barking, but they are silly. All in all- highly recommend if you want fun, satisfy, long lasting, ice rings for your tumbler. If you know someone that loves their Stanley- it would be a great gift!
Kay Kay
2025-04-20 17:14:24
Idea is good but not great. I had a tremendously hard time removing the ice from the mold. Pulling the ice away from the rubber required some muscle. The ice sticks to the rubber so in order to get it I had to break the ice first then use it in pieces. This was not the idea I thought I purchased. It was a hassle and more work than I cared to be bothered with. Who’d of thought getting ice could be difficult. I would not recommend nor repurchase. 2 stars because the idea was there.
Customer
2025-04-15 18:17:35
Worked great! High quality.
Ivette Villalpando
2025-03-23 15:52:00
Muy util, dura muchisimo el hielo en mi stanley. Mi bebida siempre fresca!
vicki
2025-03-20 10:43:33
Love the fact I have ice in my travel Mugs and the ice keeps for 24 hours. And i don't have to fight with the straw and ice
Cecy H
2025-02-23 12:56:19
La verdad estorba la caja en el congelador y solo caben los 3 cilindros de hielo en el Termo Stanley de 40 Oz en los menores no, pero el material es de calidad y cumple lo q dice el anuncio
Nickels
2025-01-25 13:10:33
Product works very well. It is suggested to wait a bit before attempting to remove the ice from the trays.
Recommended Products