Your cart is empty.
Your cart is empty.Flares and swages. Converts quickly. Screw-type feed. Ideal for use in close quarters. Two bars included cover 9 sizes. Swivel-type swaging adapters and flaring cone are hardened steel, chrome finished for easy operation. Self-centering, slip-on forged steel yoke. Includes tool case. Wt. 3.5 Ibs. Flares 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8" and 3/4" O.D. Includes 5 swage adapters for 7 tube sizes: 3/16", 1/4", 5/16", 3/8", 1/2", 5/8", 3/4" O.D.
Squirrel!!
2025-08-29 16:24:49
I really just needed this for some 3/8" copper repairs in my RV, and it did the trick perfectly. I had purchased a cheap brand first because it had relatively decent reviews. But it scraped up my tubing, wouldn't clamp down fully even then, and created an oversized swage with a gap I was pretty sure solder wouldn't be able to fill properly. Sent that back and picked this one up, and I noticed right away the increased weight between the two. The vice is much smoother and of higher quality material, didn't crimp my tubing excessively, and performed a very snug fitting swage. I would have probably preferred a tiny bit more wiggle room, but once the copper is sanded, it'll probably be perfectly fine (soldering is on tomorrow's list). I love that it's made in the USA and still cheaper than the higher end brands, but seems well made and in good tolerances.EDIT: Finished soldering and flaring 2 of the lines for a flare nut, tightened up, leak checked, and I'm in business again.
Jorge
2025-06-24 14:08:46
Gran desilusión, en las fotos publicadas dicen que es fabricación USA, lo que me llegó es imperial pero es de fabricación Tailandia
WhitetailHunter23
2025-05-21 17:27:40
I bought this because I needed a good swage kit. I don't like using swage punches. I have a really nice hilmor orbital flare kit but it doesn't come with the swaging capability so I bought this. Overall this imperial does the job it needs to do. I have only used it on 3/8 copper so far and I noticed that when I try to fit the pieces together it is pretty tight. I have used other swage kits that swage a little bigger and not so tight, but this is ok. I find it hard to clamp my piece without damaging the outside too much. I'm not a big fan of the way the clamp is set up but it works pretty good in the end. This imperial does what it is supposed to do and I can't complain too much about that. I was debating this over the Bacharach swage kit and I wish I would have gotten that one instead. I have used the Bacharach before and I like it better. As far as flaring goes, it is no where near my hilmor for flaring. I strictly neeeded this for swaging and I would much rather flare than swage anyway. If you don't want to break the bank this will perform your swaging needs however I think there are better ones out there
上田伸也
2025-02-15 13:30:13
知りåˆã„ãŒå†™çœŸã¨åŒã˜ã‚‚ã®ã€‚ケースã«å…¥ã£ã¦ã„ã‚‹é…ç½®ã€USA製ã¨ã„ã†ã®ãŒåŒã˜ãªã®ã§ã€è³¼å…¥ã—ãŸãŒã€å†™çœŸã¨é•ã†ã‚‚ã®ãŒå±Šã„ãŸã€‚評価ã«ã‚‚値ã—ãªã„。
Recommended Products
$139.77
$ 63 .99 $63.99