Your cart is empty.
Your cart is empty.Customer
2025-05-28 13:13:59
Using this an Arduino, stepper controller and belt system to make a shaker and have had no problems.
Michael T Smith
2025-05-27 17:38:23
Replaced my Y axis stepper motor after a failure. This stepper is much quieter and a direct replacement cable and all for my Hictop Prusa I3 (RepRap) clone. Good price, arrived on time, performs as expected. It's a stepper, it works, it's quiet. Not much else to say.
Dawne Short-Scott
2025-05-16 13:10:45
Purchased this to build a watch cleaning machine using a stepper motor controller running in SPI mode and the motor runs silent with plenty of torque. I will purchasing a few more in the near future
Dan
2025-05-15 17:35:36
works as expected on longer lk4 but does not work on cr10s4 ???? if anyone knows why please let me know
Yakov G
2025-05-12 09:48:55
I bought 4 of these for my large format printer -- after about a week of heavy use 1 of them started seize up. I noticed that if you compress it by replacing the stock bolts with black oxide m3 hex bolts, i could get it to move a bit better, but it still had a dead spot, the bearings are fine, but the rotor catches inside the stator on one spot -- the others are fine. I really like these since I can run the cables, and if I need to swap the stepper, it's a simple process, an no cable mess is required, I just am hoping that rest of mine don't develop the same issue, as I really like how much torque they put out and how cool and quiet they run.I was able to find a replacement while these were out of stock, as the 60mm versions are not kept in stock very often, so I gotta keep replacements on hand in case another one has a similar issue. The seller is very nice and refunded me for the seized one, and they respond very quickly. I'm gonna assume just bad luck.
Gene F
2025-03-17 20:13:56
I bought this motor (x3) hoping for a good replacement for a burned out bed motor and so far it seems to be working fine. You will need to uncross the center two wires on the connecting cable or you will get undesirable results. Switching the wires was the hardest part of this motor swap. No other setting changes were required.
LMI
2025-03-12 15:25:21
Motor usefulness is only a few months because of their JSP-ZH 11 pin connectors and wires. The issue:- They use only 4 pins out of 11. So no need for a connector with 11 pins that is impossible to buy.- Their wires are extremely brittle and broke after being embedded in an application that has some vibrations- While it's easy to get JSP-ZH connectors with any amount of pins between 2 and 10, it is impossible to find one with 11 pins- Just because of that the motor is unusable after only a few months
Rommel Pablo
2025-03-04 17:08:55
I like the availability of the item. I also like how easy and simple it is to replace the part for my 3D printer.
Cliente
2025-02-09 17:17:48
ottimo prezzo, funziona
massimo
2025-02-07 14:06:40
ok
Phil Maddox
2025-01-26 21:46:18
Installed as a light weight direct drive extruder motor and is working well. Nice that it comes with a 1 meter cable too.
Der Osterhase
2025-01-22 15:24:45
Tut zuverlässig, was er soll.
Fabio
2024-11-23 09:10:51
Ottimo motore in sostituzione dell'originale su una Anycubic Predator ..non servere invertire i fili perchè il cablaggio è già giusto...per la durata vedremo.
Recommended Products
$41.94
$ 19 .99 $19.99
$39.90
$ 19 .99 $19.99