Your cart is empty.
Your cart is empty.The CP-475 is a set of two cable pulleys designed to help install electrical, COAX, network, and other various low voltage cables. With their swivel snap hooks, deep grooves, and anti-friction bearings, these pulleys keeps cables aligned with the direction of the pull, preventing snags and kinks. Holds up to 20 CAT5/6 network cables Swivel snap hook installs easily and keeps pulley aligned with direction of pull to prevent kinks Anti-friction roller bearings and deep grooves allow cable to be pulled smoothly and easily Made from a high strength ABS plastic and zinc coated steel to provide enhanced durability and longer life Easy to remove the pulley after cable is installed Includes (2) pulleys
Peter
2025-08-27 11:42:41
These work great. It's like having an extra person on the job.
Customer
2025-08-26 14:14:40
I have found these pulleys to be invaluable for pulling in CAT6 cable or any wiring for that matter. I typically work alone and with proper placement, it is a breeze to pull multiple cables from the head end to distant terminals. Pulling around corners are no longer an issue for me, I just creatively place a pulley with a short chain or rope at the needed angle and keep going!I get a lot of comments from others on the job and I can see the wheels turning as they watch me do what normally take 2-3 guys to do with my little pulleys!The pulleys never snag or catch and are easily removed from the wires when the pull is finished. They store easily in a bag that I keep on the truck for these occasions. Giant labor saver, well work the money spent!
Ryan Konrath
2025-08-09 18:29:27
I will NEVER pull cable again without these pulleys!! Normally I'm pulling cable by myself, so anytime I hit a bend or a turn, I have to stop and pull a bunch of slack. Not anymore!! I've pulled CAT6 ~200ft through 4 bends like it was nothing! In the attached pictures, I'm pulling fiber through 6 floors of IT closet including a zig-zag where one of the floor penetrations didn't line up with the rest, and it was laughably easy! Yes, those are fiber jumper cables, not meant for pulling, so you can't really put any tension on them when pulling, and with these pulleys I didn't have to. I started out with just 2 pulleys and one of the drop-ceiling sleeves and they worked so well that I went and bought 2 more pairs of pulleys. I would definitely recommend grabbing some paracord & a pile of carabiners to go with these. They'll be a huge help in getting the pulleys placed where you need them.
Kyle
2025-05-16 11:23:24
I’ve been using these in an industrial oilfield setting and they’re holding up to the wear and tear just fine. Buying more soon.
Old Radioman
2025-04-21 18:14:23
I use four of these cable pulleys for pulling bundles of low-voltage and Category cables through the steel trusses of large stores. Being able to pull through four directional changes without pulling loops multiple times is a real game-changer. Wish I'd had these decades ago. They seemed a bit expensive, but in the end they're worth every penny.
Casey
2025-04-15 10:45:35
These pullies help monumentally on single man pulls with 90s in them. Only negative is I feel like they could machine closer tolerances for the metal arms that hold the pulley. The tolerances are tight, but I've had single cables that want to slip through the gap and go to the side of the pulley. Especially if the pull angles extreme.
James W. Self
2025-02-01 12:30:55
I pulled a warehouse by myself with these. Multiple 90s with Banana wire and cat 6 were pulled with ease. I also use these when pulling through a drop ceiling at the entrance so the wire doesn't damage the grid. Little pricey but a great product.
Jarrod Wilmoth
2024-12-07 12:15:27
Works well. I've had others in the past that let the cable roll over the edge and jam up the pulley. I've pulled cat6 and armored fiber using these pulleys. Very happy.
Recommended Products
