Your cart is empty.
Your cart is empty.Product Description
Handy & Portable
Small, portable pocket-hole jig for work on the go or in tight spaces.
Dual Positioning Sliders
Molded-in markings help you set your jig to the thickness of the material you are working with.
Wood-Chip Relief
Designed to keep the drill bit clear of excess wood chips, minimizing drill-torque, increasing the longevity of your drill bits, and allowing you to complete a perfect pocket hole in just one plunge.
Roger A. Knopf
2025-08-31 17:40:12
I have been using Kreg jigs for many years now, and have this item's predecessor. While I could not live without it, a few things always bugged me - and they all got fixed in this version. It was enough that purchasing it was a no-brainer.The biggest improvement is the built-in offset lip with markings for all typical lumber sizes. In the old one I had to actually screw the lip that is used to align to the edge of the board on using two screws - and if I was using 2x material, add a spacer using different size screws - and if I was using anything else I had to measure and line it up manually. Good if I was doing a lot of boards, but a real pain for one or two and worse if I was switching back and forth! With this new model, just press in on the tab and slide the gray guide forward until it snaps into place at the mark for the size board I am using.Second, with the lip in place, the Kreg clamp I was using was trapped in the jig and if I wanted to use it for something else, or just put it away, I had to unscrew the lip. Done away with in the new model, there is a spot sized for the clamp that is proud of the jig. Very easy.Third, this comes in a nice little case that holds everything but the clamp. My other was part of a set of Kreg jigs so when I wanted to throw it into the toolbag to go to a work site, I had to put all the parts in, and some would eventually go missing. Now I can put the case into the toolbag, very handy.Fourth, the jig from the old set that showed where to set the drill stop required me to lift the drill out of it in order to get the stop on, and of course it would sometimes slip when I tightened it so I have to recheck and sometimes adjust. Honestly it was such a pain that I got an extra bit and stop just so I could leave one set for 3/4" material and one for 2x material. In the new model the jig is part of the case AND holds the bit at each end, leaving space for the stop so I can tighten it without moving the bit.Clearly Kreg is listening to their customers and making very handy and sensible improvements while maintaining their high quality. Like I said, buying this one even though the old one still works was a no-brainer. Now I'll just set up the old one for 2x material and leave it.
Jon
2025-08-29 09:47:38
I decided to buy this over the $20 Kreg kit. All of the stuff that came in this kit I was going to have to buy anyway so I figured I'd get it all in a nice case. This came with everything I'd need to complete my project, everything you see in the photo above. The screws that it came with were 1", 1.25", and I don't remember the 3rd length. There are a limited amount of each so if you have a slightly larger project I'd invest in those while buying this. Luckily Home Depot had the 1.25" screws in stock so i was able to finish my project this weekend. I also recommend purchasing the Kreg Face Clamp because it's made for this product. It fits into the gray piece that you see on the back of the jig. It worked like a charm when I used it. Of course I held the jig down with my hand while screwing the pilot holese so I made sure it didn't slide around. Without a proper clamp your project will turn into a nightmare. The other nice part about this jig is that you can see it comes with the 2 slot holes, so you can make 2 holes without having to reposition or reclamp the jig over and over. I was building a mid century style tv stand so I needed to make about 4 pilot holes on each joint. Repositioning the jig does become a pain after a while. I think that had more to do with my workspace than anything. I had to use an old wood desk that didn't have a solid area to clamp to, so that took some time. Some people have said that your drill bit will hit the plastic of this thing and they are correct, but only a minimal amount in areas that really don't matter. There is the metal ring that the bit goes into and at the end of that area is plastic where the bit hits the wood. I don't see this effecting the bit down the road unless maybe I was using this thing on a very consistent basis, in that scenario I would obviously invest in much more expensive tools. This jig is for the amateur carpenter building a piece of furniture or frame here and there. For me it's a nice simple tool to have around if I ever want to make a simple piece of furniture. I don't see myself making too many so this thing hit the right price point for me. I highly recommend this to everyone.***Side note, make sure you practice on a few scrap pieces of wood to make sure you have your depths correct. Test out the connections too.
Athar Iqbal
2025-08-27 18:00:39
useful for DIY projects.
ãŠã‹ã„ã‚‚ã®ãã¾
2025-08-25 17:41:42
ãƒã‚±ãƒƒãƒˆãƒ›ãƒ¼ãƒ«ç”¨ã®æ²»å…·ã€ä¸è¯è£½ã‚‚ã„ã‚ã„ã‚ã‚ã‚Šã¾ã™ãŒæœ¬å®¶æœ¬å…ƒã¨ã„ã†ã“ã¨ã§è³¼å…¥ã€‚プラスãƒãƒƒã‚¯è£½ã§ã™ãŒä¸ˆå¤«ã§ã™ã€‚最åˆãƒ‰ãƒªãƒ«ã‚’通ã™ã¨ãã«ãƒ—ラ部分ãŒå‰Šã‚Œã¾ã™ãŒã“ã‚Œã§å…¬å·®ã‚’å°ã•ãã§ãるよã†ã§ã™ã€‚グリップ付ããªã©ã„ã‚ã„ã‚ãƒãƒªã‚¨ãƒ¼ã‚·ãƒ§ãƒ³ãŒã‚ã‚Šã¾ã™ãŒã€ã„ã¡ã„ã¡ã‚¯ãƒ©ãƒ³ãƒ—ã§æ¢ã‚ã‚‹ã®ã¯é¢å€’ã§ã™ãŒã‚³ãƒ³ãƒ‘クトã§DIYã§ã¯å分ã§ã™ã€‚ケースも付ã„ã¦ã„ã¾ã™ã€‚専用ã®ãƒ“スã¯é«˜ä¾¡ãªã®ã§ã‚³ãƒ¼ã‚¹ã‚¹ãƒ¬ãƒƒãƒ‰ã‚’使ã£ã¦ã¾ã™ã€‚åŠãƒã‚¸ã§ã¯ãªã„ビスを使ã†éš›ã«ã¯4mmã®ãƒ‰ãƒªãƒ«ã§ä¸‹ç©´ã‚’é–‹ã‘ã¦ã¾ã™ã€‚
Ridley
2025-08-20 11:47:18
This is my first pocket hole jig so I may not give the best review with no reference. But for me this is great because I just follow the instruction and then everything was like falling into place. I love the experience in using this jig
Terry Udy
2025-08-15 10:10:50
Arrive quickly and in good nick
Martin
2025-08-12 12:29:13
Mer anpassad för amerikanska standarmått, men har millimeterskala som är bra. Man kan trixa sig fram till 12mm inställning, för tjockare material så funkar det toppen att ställa in via jiggen.Skruvarna som följer med är bra, men dyra och har en kvadratisk bits. Går utmärktmed annan träskruv, man får konvertera till millimeter från deras instruktion.
Roger A. Knopf
2025-07-22 16:03:06
I have been using Kreg jigs for many years now, and have this item's predecessor. While I could not live without it, a few things always bugged me - and they all got fixed in this version. It was enough that purchasing it was a no-brainer.The biggest improvement is the built-in offset lip with markings for all typical lumber sizes. In the old one I had to actually screw the lip that is used to align to the edge of the board on using two screws - and if I was using 2x material, add a spacer using different size screws - and if I was using anything else I had to measure and line it up manually. Good if I was doing a lot of boards, but a real pain for one or two and worse if I was switching back and forth! With this new model, just press in on the tab and slide the gray guide forward until it snaps into place at the mark for the size board I am using.Second, with the lip in place, the Kreg clamp I was using was trapped in the jig and if I wanted to use it for something else, or just put it away, I had to unscrew the lip. Done away with in the new model, there is a spot sized for the clamp that is proud of the jig. Very easy.Third, this comes in a nice little case that holds everything but the clamp. My other was part of a set of Kreg jigs so when I wanted to throw it into the toolbag to go to a work site, I had to put all the parts in, and some would eventually go missing. Now I can put the case into the toolbag, very handy.Fourth, the jig from the old set that showed where to set the drill stop required me to lift the drill out of it in order to get the stop on, and of course it would sometimes slip when I tightened it so I have to recheck and sometimes adjust. Honestly it was such a pain that I got an extra bit and stop just so I could leave one set for 3/4" material and one for 2x material. In the new model the jig is part of the case AND holds the bit at each end, leaving space for the stop so I can tighten it without moving the bit.Clearly Kreg is listening to their customers and making very handy and sensible improvements while maintaining their high quality. Like I said, buying this one even though the old one still works was a no-brainer. Now I'll just set up the old one for 2x material and leave it.
Jon
2025-07-19 12:36:49
I decided to buy this over the $20 Kreg kit. All of the stuff that came in this kit I was going to have to buy anyway so I figured I'd get it all in a nice case. This came with everything I'd need to complete my project, everything you see in the photo above. The screws that it came with were 1", 1.25", and I don't remember the 3rd length. There are a limited amount of each so if you have a slightly larger project I'd invest in those while buying this. Luckily Home Depot had the 1.25" screws in stock so i was able to finish my project this weekend. I also recommend purchasing the Kreg Face Clamp because it's made for this product. It fits into the gray piece that you see on the back of the jig. It worked like a charm when I used it. Of course I held the jig down with my hand while screwing the pilot holese so I made sure it didn't slide around. Without a proper clamp your project will turn into a nightmare. The other nice part about this jig is that you can see it comes with the 2 slot holes, so you can make 2 holes without having to reposition or reclamp the jig over and over. I was building a mid century style tv stand so I needed to make about 4 pilot holes on each joint. Repositioning the jig does become a pain after a while. I think that had more to do with my workspace than anything. I had to use an old wood desk that didn't have a solid area to clamp to, so that took some time. Some people have said that your drill bit will hit the plastic of this thing and they are correct, but only a minimal amount in areas that really don't matter. There is the metal ring that the bit goes into and at the end of that area is plastic where the bit hits the wood. I don't see this effecting the bit down the road unless maybe I was using this thing on a very consistent basis, in that scenario I would obviously invest in much more expensive tools. This jig is for the amateur carpenter building a piece of furniture or frame here and there. For me it's a nice simple tool to have around if I ever want to make a simple piece of furniture. I don't see myself making too many so this thing hit the right price point for me. I highly recommend this to everyone.***Side note, make sure you practice on a few scrap pieces of wood to make sure you have your depths correct. Test out the connections too.
Athar Iqbal
2025-06-13 14:04:18
useful for DIY projects.
ãŠã‹ã„ã‚‚ã®ãã¾
2025-06-04 13:35:45
ãƒã‚±ãƒƒãƒˆãƒ›ãƒ¼ãƒ«ç”¨ã®æ²»å…·ã€ä¸è¯è£½ã‚‚ã„ã‚ã„ã‚ã‚ã‚Šã¾ã™ãŒæœ¬å®¶æœ¬å…ƒã¨ã„ã†ã“ã¨ã§è³¼å…¥ã€‚プラスãƒãƒƒã‚¯è£½ã§ã™ãŒä¸ˆå¤«ã§ã™ã€‚最åˆãƒ‰ãƒªãƒ«ã‚’通ã™ã¨ãã«ãƒ—ラ部分ãŒå‰Šã‚Œã¾ã™ãŒã“ã‚Œã§å…¬å·®ã‚’å°ã•ãã§ãるよã†ã§ã™ã€‚グリップ付ããªã©ã„ã‚ã„ã‚ãƒãƒªã‚¨ãƒ¼ã‚·ãƒ§ãƒ³ãŒã‚ã‚Šã¾ã™ãŒã€ã„ã¡ã„ã¡ã‚¯ãƒ©ãƒ³ãƒ—ã§æ¢ã‚ã‚‹ã®ã¯é¢å€’ã§ã™ãŒã‚³ãƒ³ãƒ‘クトã§DIYã§ã¯å分ã§ã™ã€‚ケースも付ã„ã¦ã„ã¾ã™ã€‚専用ã®ãƒ“スã¯é«˜ä¾¡ãªã®ã§ã‚³ãƒ¼ã‚¹ã‚¹ãƒ¬ãƒƒãƒ‰ã‚’使ã£ã¦ã¾ã™ã€‚åŠãƒã‚¸ã§ã¯ãªã„ビスを使ã†éš›ã«ã¯4mmã®ãƒ‰ãƒªãƒ«ã§ä¸‹ç©´ã‚’é–‹ã‘ã¦ã¾ã™ã€‚
Ridley
2025-03-13 12:45:33
This is my first pocket hole jig so I may not give the best review with no reference. But for me this is great because I just follow the instruction and then everything was like falling into place. I love the experience in using this jig
Terry Udy
2025-02-19 13:10:11
Arrive quickly and in good nick
Martin
2025-02-09 12:44:14
Mer anpassad för amerikanska standarmått, men har millimeterskala som är bra. Man kan trixa sig fram till 12mm inställning, för tjockare material så funkar det toppen att ställa in via jiggen.Skruvarna som följer med är bra, men dyra och har en kvadratisk bits. Går utmärktmed annan träskruv, man får konvertera till millimeter från deras instruktion.
Recommended Products