• Support perfect fade-in and fade-out switching.
• Support image display enhancement on brightness and contrast.
• Support double-window display for arbitrary roaming among PIP, POP and window location.
• Support arbitrary frame size zooming (The window is adjustable point by point, able to bereduced to a pixel).
• Support the motion compensation to eliminate picture tailing.
• Support to save and call five scene modes.
• Support shortcut settings (smart settings) of the navigation

Package Included:

1XU2

1X User Menu/ a Disk

&Cables

Installation Steps:

• 1,Make sure the led screen displays image normally when the graphics card controls sending card directly and the video processor is absent.
• 2,Connect DVI port of graphics card to the DVI-IN of the processor,then connect DVI-OUT of the processor to sending card.
• 3,Power on the video processor after cables are connected accurately.

Note: For the convenience of customers, the sending card can be loaded or unloaded in the processor, i.e. the sending card can be installed in the processor and powered by the processor, which can get rid of the shackles of desktop power supply. The installation method is as follows:

• 1,Remove the fixing corner of the sending card;
• 2,Loosen the knob on the rear panel, pull it out and remove the temporary baffle;
• 3,A small four-wire plug is reserved in the processor. It corresponds to the wire groove in the sending card. Connect it and fix the sending card on the video processor;
• 4,Reinstall and fix the drawer box, and connect the superimposed DVI interfaces.

Q&A:

• Q1: Is this processor compatible with a nova star sending card or the linsn sending card?
• A: Yes nova star or linsn work perfectly, we also have our own sending card named S6 made by Kystar.
• Q2:Can i use for a LED video wall and just need to buy a received card?
• A:You will need a sender card to put in the unit. It has slots to allow for two sender cards and power cables for both of them.You asked about a receive card - those cards are actually in the LED panels.

• Q1:Please briefly describe the connection of graphics card, video processor, sending card, receiving card and LED screen.
• A: The DVI (VGA) output port of the graphics card is connected to DVI-IN (VGA-IN) input of the video processor, DVI-OUT output of the video processor is connected to the sending card, the sending card is connected to the terminal receiving card in the back of the screen through the network cable, the receiving card is connected to respective screen and the entire large screen by cascading.
• Q2:What does the output resolution mean? Shall we set it well in advance?
• A:The output resolution refers to the maximum range of the processor output and its value is OKas long as it is greater than the actual pixels of your LED display; it will change automatically when youare adjusting the image parameters, so basically it doesn’t need to be set in advance.
• Q3:How to set up the keyboard lock of a video processor? How to unlock it?
• A: Click “MENU – Advance Menu – Expert Settings - Keyboard Lock” to lock the keyboard and youcan press the MENU button for consecutive 6 times to unlock it.
• Q4: What is the administrator password in the host PC software settings?
• A: No password is provided and you can just click “OK” to enter directly.
• Q5: What’re the reasons for the connection failure of serial port of the processor software?
• A: Connection failure may be caused by the followings:1, COM port selection error; simply click OK and then click the "Open serial port" button;2, Serial port is occupied; do not open two or more software windows at the same time;3, Serial cable is not connected or cable is damaged;4, COM driver of motherboard is damaged or serial port is damaged.
• Q6: It is normal when the graphics card is connected to the sending card directly, but the screen will appear black when it is connected to the video processor.
• A: Check if the green LED of the sending card flashes normally; if yes, the processor output port has signal, and the possible reasons may be:
• 1,Problem of signal source: The replication mode of the graphics card should be set before connecting to the computer; if not, DVI port of the graphics card doesn’t have data output. Setting steps: Turn off the video processor - reconnect the cable from the graphics card to the video processor - ATI graphics cards automatically read the replication mode; for NVIDIA graphics cards, enter the control center, and set up multiple monitors + dual screen mode.
• 2,Problem of the cable: If the signal cable is poor in connect or the wire has problems, the big screen will have color strips,blurred screen and other irregularities.Carefully check if the pins of the signal cable are squeezed or inclined and replace the signal cable.