Your cart is empty.
Your cart is empty. Packaging includes:
1 x 4100E receiver
MrEd
2025-08-28 15:06:00
As others have noted, there’s no documentation included. The negative pins are furthest from the board. If connected incorrectly, the LED just “blipsâ€, connected correctly, the LED stays on. Bound to my very old Dx6i with no problem.
Michael
2025-08-21 13:00:49
These are great little receivers. No problems whatsoever. I am wondering if the users who said they will not bind were binding it properly. The way the pins are, it’s very easy to miss a pin so that things are not plugged in correctly. I had trouble binding until I realized I did not have all the plugs in place correctly. Fix that mistake, and they work great. For me, just as good as more expensive receivers. I could not find any instructions, but had no trouble because they bind just like any other spectrum receiver. So these might not be the best receiver for a novice who doesn’t understand how to use them
sportfury440
2025-08-07 09:32:33
Claims to be a DSM2 compatible reciever. Not sure if I got a defective unit or if product simply does not provide DSM2 capability. I have multiple DSM2 recievers working all across these 3 radios.
Nick Zito
2025-07-18 13:34:37
Bound to my Spektrum NX6 transmitter no problem. Using it in a home built Great Planes airplane. As others mentioned there was no documentation but just followed the instructions that other reviewers have posted. I will buy it again in my next plane.
101101
2025-07-02 12:22:07
Bound easily to Spektrum DX6e.Pinout is attached in photo.Input Voltage Range: 3.6-10vModulation: DSM2 /DSMX-------------------------------BINDING iNSTRUCTIONS:-------------------------------1. Put the binding harness into the Channel marked BIND. Next apply power to the receiver. Receiver’s LED should illuminate.2. To set fail-safe throttle and control surface positions, (minimum throttle and all control surfaces set to neutral is suggested). Press and hold the bind button of transmitter (LED will illuminate), Turn on the transmitter.3. Receiver LED will change from rapid flashing to slow flashing and a few seconds later when bind is accomplished the LED of receiver will illuminate solid. All fail-safes should be programed correctly now.4. Remove binding harness from the BIND channel. Restart the receiver by cycling it power off and turn on. All channels should function properly now. You may test fail-safe by holding sticks in corner, cycle transmitter on and off. Surfaces and throttle should return to your preset fail-safe positions.
JS
2025-06-16 11:34:16
I was building a Flite Test plane that would be less than 250 grams. I needed a receiver that would work with my Spektrum transmitter and 5 gram servos. This does the job. I suspect that it will have a very short range but I’ll be keeping the little plane close to me.
Jim Plake
2025-06-09 20:16:52
This is complete junk, do not buy. I checked out the supposed "bind instructions" posted on here by another user. 1st off, the picture shows the negative pin closest to the board. It will not light up when powered that way. I found that it lights up when the battery negative is plugged farthest from the board. When done this way the light comes on but does not flash. I tried it with the binding plug in the far left position just like the picture and it never flashes. Am I wrong? I will not bind to either one of my transmitters. EDIT- I tried it again, following the instruction and this time it worked. I still have not tried it in flight but it does work on the bench.
Mentaloid
2025-02-14 12:02:09
Works well for light build planes. Perfect for spektrum. Easy to bind.
helena
2025-02-12 11:05:15
This reciever is lightweight and provides good range. Basic without bells or whistles which is exactly what I needed.
Pierre Boivin
2025-01-21 20:33:16
je l'utilise sur un bateau remorqueur a l'echelle et fonctionne tres bien avec ma spektrum dx9
James Stoddart
2025-01-05 12:44:07
It binds fine until you change the battery. So you can bind it, remove the bind plug and then fly. When you unplug the battery, it forgets and needs to be bound again to get a solid light.
Marshall Patterson
2025-01-01 17:40:49
Connected to Spektrum DX3 no problems, but didn’t realize it’s not for car/truck. Other than that it does work.
Igor Butenko
2024-11-24 16:29:49
For spectrym
Recommended Products
