In short, I bought this. Installed it myself. Survived the experience. Glad I did it. Want a ridiculous amount of detail? Keep reading.PLEASE NOTE: Below I refer to parts that are included with MORryde’s CRE3000 and NOT with this shackle upgrade alone. Don’t think you’ll be able to do everything I describe below with only the shackle upgrade. I posted essentially this same review for the CRE3000 since they go together.On impulse I decided to upgrade the suspension on my 2006 26' travel trailer. Myself. In my driveway. I've never done anything like this before, but how hard could it be?So without revealing to my wife my grand plan to turn our driveway into an RV maintenance yard, I ordered the CRE3000 and (since I'd be removing the wheels and rusty bolts anyway), I decided to upgrade the shackles as well with the MORryde heavy duty shackle kit. I think it's called "wet" because you can lubricate it. ( .Additional stuff purchased, using this project as an excuse, included: A 2 ton floor jack with a 23+ inch lift (enough range to lift my trailer at the frame). A grease gun (for the zerk fittings on all the new bolts ). A 24" breaker bar (rusty bolts are fun!). A can of B'laster (. A set of impact sockets for my air powered impact gun. Two tall jack stands (tall enough to support the frame jacked up). Some work gloves.Additional stuff I used that I already had on hand: An air compressor. Air powered impact gun (pretty excited about my 2nd opportunity to use it in 10 years). A second, much smaller floor jack (I didn't expect to use this, but it was VERY handy to have - details below). A creeper/crawler borrowed from a neighbor. Two small jackstands for supporting the disconnected axles. A couple wrenches of appropriate size for my bolts. A rubber mallet. A hammer. A punch.I planned to tackle the project with my 13 year old able assistant on a Saturday afternoon. So starting Thursday, I began soaking the eleven year old bolts/nuts (7 on each side of the trailer) with B'laster hoping to make them easier to remove after a couple days of soaking.Saturday afternoon I hauled the trailer out to the driveway, jacked it up, placed the two tall jackstands to support the trailer, and removed the two wheels (on one side), revealing the entire suspension. Then, thinking it might take a some pressure off the leaf spring and bolts, I lifted each axle just a little bit and supported them with small jackstands. Now it's time to remove those rusty old bolts.So the bolts faced away from me. That is, they were inserted with the head toward the outside and the nuts on the inside (under the trailer). No problem. I put a wrench on the backside to hold the nut in place, and then used my air-wrench to turn the head. Or tried to. Didn't budge the tiniest bit. Then I hung my 13 yr old off the end of the breaker bar. Then I hung myself off the end of the breaker bar. Didn't budge the tiniest bit. More P'blaster, a little banging with a hammer to try and free the frozen bolts. No joy with any of the 7 bolts. I was extremely frustrated and had to really bite my tongue to avoid language my assistant shouldn't hear. Until one bolt finally gave just a little bit.At this point, some of you more knowledgeable folks already know my mistake. It turns out the bolts themselves (on my trailer) aren't intended to turn. Near the head of the bolt is a small area of grooves that locks the bolt in place. The nut has to be removed from the stationary bolt. At least until the nut backs off far enough that the bolt can be tapped out past the grooves and then turns as you might expect. So learn from my mistake - apply pressure to the nuts, not the bolts. I wish I had learned this lesson an easier way, say by looking at the brand new replacement bolts, seeing the grooves and realizing their obvious purpose. But that's not my style. Plus it was a lesson in perseverance for my assistant. If at first you don't succeed, cuss, hit it with a hammer, nearly give up, and then get lucky.Anyway, after the bolt design revelation things started moving much faster. Between the air-gun and breaker bar all the nuts came free without too much difficulty. The creeper and small size of my assistant (compared to me) was invaluable in removing the nuts under the trailer. Thank goodness for sturdy jackstands and his mom staying in the house.Then we used a punch to knock the bolts out, freeing the leaf springs and removing the triangular center hanger. More use of the punch to push the worn OEM plastic bushings out of all the bolt holes. Now disassembly is complete.Reassembly was mostly straightforward. Insert the shiny brass bushings (from the shackle kit) into all the bolt holes and gently tap in with rubber mallet. Hang the new CRE3000 in the center and drive in the center bolt, put the nut on the back, but not tight yet. Reattach the leaf springs to the left & right of the CRE3000 using the new shackles and bolts from the kit. One tip - on the center bolt (that hangs the CRE) the zerk fitting in the head of the new bolt faces outward toward you. On ALL other bolts, the zerk fittings face inward, under the trailer. That's supposed to make it easier to reach and lube when the tires are on. So unlike the original bolts, all the nuts except the center bolt will now be on the outside rather than inside. That'll be handy in the future when I forget the lesson learned above.The left & right ends of the leaf springs that attach to the front & rear frame hangers can be a little tricky to get aligned so the bolts will go through. The holes will be too high, too low, or crooked. This is where I used my small floor jack to push up on the end of a spring raise it, or push down on the spring to lower it. To push down on the spring, I set the jack on TOP of the spring and pumped it up until the jack foot hit the frame above. Than as I continued to pump, the jack pushed the spring down aligning the holes. It took a bit of fiddling, including with the axle jack stand, to get the leaf spring ends reconnected, but in the end it wasn't really hard.The last step was to tighten all the nuts and lubricate the 7 bolts with the new grease gun. Then we we replaced the tires and we were done. With one side. It had taken us about 4 1/2 -5 hours and daylight was running out. We finished the job the next day and, with the lessons learned, it took only about 2 1/2 hours to finish the second side. So roughly seven hours total including the time penalty for stupidity.We went for a test drive and I immediately noticed two things. First, the tires/axles didn't immediately fall off. That was a relief. My mind had been full of "what ifs" and "what did I forget?" and "where did that extra bolt come from?" (just kidding). The second thing was how QUIET the trailer was. I had gotten used to lots of squeaks and squeals over speed bumps and maneuvering at low speed, but now the trailer is whisper quiet in all circumstances and seems to float along behind the truck rather than bounce. I'm very pleased with the end result and glad I chose to do it as a DIY. It was actually a very satisfying project to complete with my son.

Destroyed 2 leaf spring straps this past fall on our TT on the way home from a camping trip and had to drop the trailer at a parking lot, drive to Tractor Supply and pick up a strap repair kit to get the TT home. Your $30 -$40k trailer or 5-er is riding on super cheap, thin, inadequate suspension components and when mine broke (both on the drivers side rear axle at the same time) almost cost me my trailer... Upon inspection, all the suspension straps were showing signs of wear and needed to be replaced. The Mor-Ryde wet bolts kits are much stronger than the factory stuff, greasable, and much quieter. I liked the kit I installed on my TT so much that I ordered another set and installed them on my 16' Utility trailer, which had the same weak factory junk on it... Remember that trailer manufacturers use the same "contract to the lowest bidder" mentality as the Govt. The install takes a bit of work, but not bad if you are good with rusty old stuck bolt removal, and have basic hand tools, multiple good jacks/jack stands, a torque wrench, and about 3 hours time...

The factory pieces where much thinner compared to the wet bolt kit and the brass bushings too, these are heavy duty, rugged, and greaseable makes it last much longer. I installed the wet bolt kit along with the SRE-4000 kit, while i had it apart, it was pretty easy to replace all the components at the same time with a few tools. I replaced them myself and found it to be pretty easy, the first side took longer as i learned, but the second side was much quicker. I checked all the bolts again after 3 months and thousands of miles, all of the bolts were tight and doing well.

When I received my new 2017 travel trailer, the suspension was making quite a bit of noise. I removed one of the OEM nylon bushings and it was already worn through with only 1,800 miles on the chassis since it was built and delivered to Arizona.I elected to change out the cheap nylon bushings with the MORryde bronze bushings that are included with this kit. I paired it with the MORryde CRE3000 equalizers. The quality of these components are superb compared to the OEM parts that were installed by Lippert who manufactured the frame and suspension components. Check out the picture I'm attaching to see the difference in the parts. The beefier MORryde shackles should last much longer than the thin OEM version.Changing out the components was straightforward, and the instructions were clearly written. Make sure that you orient the grease holes on the wet bolts at the 3:00 or 9:00 position or you may have trouble getting grease into the parts. Even with them oriented correctly, I'd suggest a high pressure grease gun to get the grease to flow. Make sure the parts will accept grease before finishing the assembly or you may have to disassemble the suspension again to address the issue.I hope these parts last for many years. I put about 10-15K miles on my trailer every year. When they do wear out, I'll replace them with this same kit.

Great upgrade. Took about 4 hours start to finish. Just started on one end on one side and worked my way to the front. Hardest part was getting the nylon bushings out of the spring eyes. Greased the new bushings before installing them. Got mine for about half the price they are asking now.

Eliminated all the squeaking and creaking on my 5th WheelUsed on my 2007 Cougar 276RLS 5th Wheel. (7300 lbs dry Tandem Axle) I installed it myself with some help from a friend. You can buy the kit and take it to a shop and they will install it for you. I would do it ASAP on your trailer. It took all the squeaks and creeks out and smoothed out the towing experience. It 10X better than your stock set up unless you have “wet bolts” already. It is completely serviceable (unlike the factory stuff) and is easy to grease. When it’s easy to grease then you’ll do it. I actually have mine greased every time I get it inspected ( yearly here) and usually once in the season. The more miles you tow the more often you need to grease up. It’s the same for your wheel bearings on your trailer… something most people rarely do themselves unless you have the easy lube style of hubs.The last time I got my trailer inspected the Mechanic said that’s the best thing he ever saw on a trailer and thinks all trailers should have them…. He works on trailers all the time and says the suspension is always the weak point but with this product not so much so…..So do yourself a favour and install these on your trailer - especially if you travel long distances.

I ordered this for my American style caravan on Saturday afternoon and absolutely amazingly it was delivered direct to my door on the Monday . The parts were exactly what I wanted .Awesome

I have installed these on every trailer we have owned allong the armor road after market kit .Anyone who uses their trailer often need to install these. It makes everything work well and the nylon bushings that come with the camper wear out very gast leading to failure. Thheae are greasable and will lst a very long time if maintained properly

Well worth the money, anything that gets grease last longer plain and simple!!

Installed these along with the Mor-Ryde equalizers on my trailer. Had a buddy help me out. Installation is DEFINITELY NOT a one man job. Took us 2.5 hours to do one side and about 1/2 that time to do the other. Make sure that you have a couple of small hydraulic jacks available to help move the leaf springs back into position after you remove the fastening bolts. Otherwise, it is pretty straight forward.Looking forward to see how they perform on our extended holiday this summer out west.