Your cart is empty.
Your cart is empty.Park Tool's thoughtfully designed P-handle hex wrenches always fit the task at hand, and they fit in your hand too. Each wrench features a ball end on the long side for access to hard-to-reach fittings and a straight chamfered tip at the handle for higher-torque applications. The hex wrenches are made from high torque industrial steel and through hardened for long life. Available in a full range of sizes to fit any metric hex fitting found on a bicycle, Park Tool P-Handle wrenches are up for any task of removal, installation, or adjustment.
rocknrick
2025-08-13 12:53:09
I bought this to remove old Wimberly foot plates from telephoto lenses. (It's easy to strip/damage the heads of these important screws that hold Arca-Swiss type plates onto expensive lenses; if these plates fail, it could result in the damage of expensive equipment.) This Park Tool was absolutely perfect to help me in removing and replacing these camera plates. The Park Tool is long (allowing me to go deep into the screw wells), sturdy (lots of torque was placed on the tool, but it did not bend or break), and comfortable (the T-handle is well designed). Thank you Park Tool for such a great tool.
AmyFranklySpeaking
2025-06-16 17:26:39
My 10 year old's bike was ordered and delivered put together. The handlebars were slightly off and I used every tool I had to try and loosen that bolt to adjust and nothing worked. It was so tight, I couldn't even get a drill to move it. So I had to order this thing. And just like that, easily loosened, adjusted and retightened the bolt. The length of the shaft is just right for the torque needed to loosen the bolt.Handy tool to have. Not sure what else will need the exact same size other than the bike, but useful to have around at an inexpensive price.
decisivemoment
2025-06-06 11:32:46
Park's P-handled hex wrenches are extremely useful in the 4mm and 5mm sizes for running adjustments on gears and brakes. They're very strong, and give far more control on these adjustments than typical Allen keys. The reach is useful and the handle design gives you a lot of purchase on the screw. The metal appears to be strong enough that you can get away with using the ball-joint end with a fair bit of force. I'm not sure what the purpose of buying the full set is, though; there are few uses for the 10mm version, and as for the 8mm, the most common setting there is pedals and that's high enough torque I'd prefer to have the handle on the ball-tip end of the wrench rather than the square tip end (no point trying to tighten or loosen pedals with a ball-tip). But for up to 5mm (and in select cases 6mm) this is a very nice tool to have. Probably I'll add a 3mm version as well, at least at such point as I replace my JIS#2-limit-screw-equipped derailleurs with the latest 3mm Allen-key-adjustable ones.
Djh
2025-05-30 12:48:14
Short bit loosens tight bolts. Long shart turns them out quickly. The rounded tip allows access to hard-to-reach bolts.
Shadow
2025-04-29 18:48:05
I needed this to replace the one that came on my daughter's wheelchair. It's used to make minor adjustments to the headrest and such. The one that came with the wheelchair is mounted to the back of the chair for easy access. It was almost a foot long to provide the required torque but must have been made from soft steel because it didn't take very long to round over the edges to the point where it was no longer usable. I considered just grinding off the ends but decided to look for a more durable replacement. This wrench is well made, durable and fits nicely on the back of the chair. It fits comfortably in my hand and is long enough to apply the necessary torque to properly tighten the adjustment bolts. I highly recommend this wrench!
Joseph caissie
2025-04-19 20:47:46
It fits LMAO and works.. i hope you enjoy my in depth review of this hex wrench. Ready... The angle of the hex seems to be just right the wrench seemed to fit perfectly into the corrosponding nut and with gentle twisting force it seems to loosen or tighten said nut i highly recommend this hex wrench because it works on hex bolts LMAO it's fine quality is as expected of you need one this one is fine just get it
Kyleiniowa
2025-03-28 15:59:06
You get what you pay for, Park Tool is worth the money. Great stuff.
CEC732
2025-02-19 14:40:15
Nice quality wrench. Highly the recommended.
Danny
2025-02-06 14:53:33
quality tool.
ETF UK LTD
2025-01-06 18:31:01
No problems
Steve Parker
2024-12-24 13:38:36
Picture is more than misleading, was expecting a full set of Allen keys. Should of known better as quite cheap but picture is more than misleading.
Pedro P.
2024-12-15 14:11:24
Buena construccion, vale la pena pagar de mas
WD
2024-11-16 12:31:07
Good quality and is better to use than ordinary Allen keys. Does not scratch screw coatings during use. Would recommend!
Recommended Products
$33.27
$ 16 .99 $16.99
$25.99
$ 12 .99 $12.99