Your cart is empty.
Your cart is empty. Product Description
With the popularity of USB 3.0, more and more computer cases offer a 19-pin USB3.0 port on the front of the case,
but the old motherboards do not support USB3.0 or do not have a 19PIN interface!
At this point, you can convert the PCI-E signal to the 19-pin USB3.0 port and 2 rear USB3.0 ports via the motherboard's PCI-E slot, and then convert the 19PIN of the panel to the Insert expansion card so that it offers the front super high-speed USB3.0 interface is very practical!
Specifications:
※ Compatible with the PCI Express specification version 2.0
※ Compatible with the USB3.0 SuperSpeed specification version 1.0
※ Note the xHCI specification version 1.0
※ Master chip: Renesas UPD720201 chipset
※ Applies to all PCI-E -Sockets
※ The highest transfer rate is up to 5 Gbit / s, which is much higher than 480 Mbit / s from USB 2.0, which is up to 10 times.
※ Backward compatible with USB2.0, USB1. 1, USB1.0
※ Transfer rate: 5000/480/12 / 1.5 Mbit / s
※ USB output: up to 5V 2A (increased current type)
※ Integrated SATA-extended power interface
※ Supports di e USB hot plug function
※ Support Windows XP / 2003 / Vista / win7 / win8 / win10
Hardware requirements:
This product is a desktop PCI-E expansion card which requires a free PCI-E slot on the motherboard for installation and use.
Also determine if the slot is blocked by the graphics card.
The PCI slot cannot be installed and used. Never install the expansion card in the PCI slot.
Packaging accessories:
A: USB3.0 expansion card * 1
B: Driver CD * 1
C: Low-profile bracket * 1
D: 4 pin Molex to SATA power cable * 1
Huevos Rancheros
2025-08-29 10:03:38
Great card, fast speed, brackets fit properly for small slots in pc. This card was great for adding usb3 to an older Digital Audio Workstation build. Card comes with everything you need to get setup, except the cable for adding ports to the front of your computer, you can either use your existing one and plug it into the card, or buy one.The only (minor) issue was when it came for the driver installation, there are 2 versions of the card drivers on the mini cd-rom. I wasn't sure which card I had. It wasn't described in the .pdf manual either. I pulled the card and checked the printing on the card and it wasn't clear either. I finally went back to amazon and looked at my order to see that I had the "Gen 1" version.Now I could install the correct drivers and it worked perfectly. so a sticker on the box or on the board would save some time, but its not a real big deal and I marked the box so If I pull this card to use in another computer in the future, I'll know which driver it needs.Card worked greate. I copied 1/2 tb over a usb3 hub and it took 8 hours. I copied that same 1/2 tb directly over the usb3 ports on this card, and it took 3 hours. so great speed and reliability.Great price, great card..
Grandma Moose
2025-06-29 16:53:11
This is the 2nd USB 3.0 card I tried in my 13 year old computer having only USB 2.0 ports front and back, as the 1st card I tried was unpowered and wasn't providing enough 'juice' to operate all my portable HDDs. For this card I used a spare SATA power connector which gives it the kick I need to run all of my various portable hard drive units with no problem. I also had to purchase a ribbon PCI-E cable extension in order to allow the use of this card as I have a large GPU card which sits right over the top of my PCI-E X1 slot. Luckily, Amazon sells those as well for under $10 so I pulled the graphics card, installed the new ribbon cable with 90 degree connectors on each end to get around the graphics card and connect up the new USB 3.0 card. After getting my old eMachines ET-1831-07 all back together, I installed the Beyimei driver CD, (as I'm running Windows 7), and it loaded very easily and I was ready to go. Does it work?? You Bet! Wow, what a vast improvement over the 1st unpowered USB 3.0 card I tried - this card will power up any and all my various external drives without a hiccup. Why didn't I install this Beyimei card in the first place?? IF you're planning to upgrade an old USB 2.0 PC to USB 3.0 and you're going to be running old external HDDs, my advice is to install THIS card as it works Great with older systems and has plenty of power for whatever needs you have and it's a complete kit for less $$ than the unpowered USB 3.0 card. And now I'm installing a PNY SSD and will just use my old WD Black HDD for backup ~ my old eMachines ought to Love That!
John
2025-06-09 10:34:54
The product came with a mini CD containing a Windows device drive.I plug it in Dell OptiPlex's PCI-E 1X slot. Installed the Windows device drive (available in the mini-CD).It works fine.I am using Windows 11 Pro.
Ragmats
2025-06-08 15:06:00
I installed this into my new PC and the front panel USB ports would only give power but no data transfer. After many hours of troubleshooting, I resorted to emailing the vendor (which I found at beyimei.com) because the product was not listed on their website. They emailed me the correct drivers and now the card is working, despite the listing saying Windows 11 does not need drivers. 1 star deduction for the hassle. Save yourself some time and get the drivers ahead of time while you wait for your order to arrive.
Jason Arnold
2025-05-28 17:53:43
When I built my PC earlier this year, I ended up breaking a pin off of the internal connector for the front panel USB ports. Only one of them would transfer data after that. Well, for
Rockyhaferkorn
2025-05-08 12:16:27
det fungerar bra
Veselin Kolev
2025-05-07 16:10:45
Velocidad de escritura en mi HP Compaq DC7900 SFF: 90-120 MB/sec.Ruta de información: SSD externo SATA3 - placa principal SATA2 - HDD interno SATA3
Jason
2025-05-05 15:16:08
Excellent product, hassle free, works immediately without any software. Nice and small and out of the way.
Angel Pérez
2025-04-27 12:45:15
Funciona muy bien insertado en una antigua tarjeta principal H81-C que no cuenta con conector USB 3.0 de 19 pines necesario para habilitar un puerto USB 3.0 al frente del gabinete.
Jorge Augusto
2024-11-16 19:21:50
Instalação muito simples: bastou colocar a placa no slot e não não necessitou de instalação de software para trabalhar em Linux.O único problema detectado foi que as portas USB não são detectadas para boot, mas poderá ser alguma configuração que não fiz na UEFI ou limitação da motherboard.
Recommended Products
