Your cart is empty.
Your cart is empty. Universal pH Test Paper
Our universal pH test strips not only use for testing your body pH level by using Saliva or Urine , but also widely apply to science education, lab use, household drinking water, swimming pools, spas, aquarium, hydroponics and more.
Key Features:
Our pH test strips offer 0.5 accuracy rather than 1 accuracy, maximum 4 colors panel that give you the most accurate results
Full pH measure range 0-14
Easy to read against pH color chart intervals
Compact size, easy to carry out
Instruction:
1. Dip the strip into the solution for half second, allow all 4 panels to get wet and then remove from the solution. The color will change almost immediately.
2. Match panels to the pH diagram on the box to get the pH reading, pH ranges from 0 (very acidic) to 14 (very alkaline).
Package Include:
1 x pH Test Paper
Stew
2025-06-09 15:48:03
I test my well water's pH. These test strips give consistent results. I cannot tell how accurate they are because I do not have a standard which to test the water's pH level and compare the results. I tested the water with a kit from a local home store that had only one pad on the strip for pH and got a 4.0 result. With these, I get a 6.5 pH reading. I tend to believe these test strips over the home store's test because one pad changing color is not very precise, and 4.0 is very low. A pH of 6.5 seems a lot more reasonable. These test strips have four pads for different ranges of pH, which is more accurate than looking at just one square.
cqw
2025-04-03 11:10:47
I am using these PH strips to test PH of soaps and lotions I make. The stips themselves are stored in a small and rigid plastic container that is easy to open and get the strips out. I bought the single color ones before and felt like I was never sure if I was reading it correctly, and turns out I was not. The color difference seems a bit more obvious with these and I feel more confident about the result.
st
2025-03-02 12:46:28
I used these to test the pH of several samples of river water for a school science project. They are a little tricky to read because the colors are so similar, but when compared to other pH strips I would say they are accurate enough. If you are looking for very accurate readings, I would purchase an electronic meter, but these are good enough for science projects and such.
Sammie
2025-02-07 10:24:56
Great item for more accurate pH readings!
woollymammoth
2025-02-02 16:07:52
The color on these strips CHANGES over the space of two to three minutes following removal from the tested liquid. I couldn’t tell whether I should take the reading immediately (as I THINK the very cursory directions on the package were suggesting) or wait for three minutes till no more color changes occurred. (If anyone knows the answer to this, please do advise. I will gladly revise my rating upward if the fault lies with my usage ignorance rather than the product.)
thesoupnawty
2025-01-30 18:59:13
I purchased these test strips for use in hydroponics as a backup to my digital ph tester. I tend to distrust anything with a digital output, and I try to accompany it with something a bit more accurate. This product was not accurate, which has been noted in many 1-star reviews already.- After dipping the strip into your intended test solution, water will often pool onto some of, or all of the 4 colors. - If you're lucky enough that the colors don't run, you will then hold the strip up to the color grouping that best matches the colors on your strip.- In order to best compare your test strip with the included Color Guide, be sure to do so under a significant amount of lighting, and then pull the guide out of the plastic case when comparing, which will help cut down the glare. (both done to help differentiate the color ranges on the Guide)- I usually find myself bright areas in the house that are being lit via incoming daylight. When I do this, I can very easily see the differences of colors on the Color Guide.I require a 5.5-6.5 ph, and 100% of the time, I cannot determine the correct ph level on the guide between that range, because the upper most color is of a dark blue, and the dark blue on the test strip is NEVER comparable to any of the uppermost blues on the guide.I suspect the fault for this lies with the Color Guide itself.- If the color guide is being produced with inaccurate color selections from the printing software, or being produced from a copy of a printout, that would alter the saturation of the colors being printed, thus resulting in inaccurate levels..In hydro, finite accuracy is fairly important, and due to the color discrepancies, these just don't provide that.If you can accept the ph being within a range of 1.5, then these strips will be just fine for your purpose.I welcome a response from Esee Group and will update my review upon receiving new information.
vac
2024-11-21 14:43:15
I recently purchased several different ph test strips for my daughter to use for a science fair project. These are the absolute best and most accurate of the test strips I bought. They are as accurate as test strips can be.The colors don't run, unlike some of the others I tried. And they measure in increments of 0.5. They read what they should for the solutions I tested these with (a mixture of water and baking soda for a basic test, vinegar for an acid test, and Evian water for a neutral test since Evian is bottled to be consistently around a ph of 7.2).For those of you trying to use these or any strips to test ph of water, please be aware that all ph test strips will be inaccurate for *most* waters, unless you take special steps (see below). Most bottled water, as well as most tap water, is low ionic strength. Test strips for ph do not work well for low ionic strength liquids (even the ones that say for water). There are some exceptions. Mineral and artesian waters, such as Evian, are higher in ionic strength due to much higher levels of total dissolved solids. For these waters, ph test strips will work fine without altering the testing procedure, including those that indicate for saliva and urine testing only.Some reviews complain about accuracy due to testing with distilled water and not getting a reading of 7.0. Distilled water has nearly 0 total dissolved solids. No ph test strip will work under those conditions. Most mineral waters and artesian waters will tell you on the bottle what its ph is. E.g. Evian claims 7.2. These test strips give a reading of 7.0 in this case and you can't get closer with 0.5 increments.For these strips, or any strips, to work, the total dissolved solids must be greater than 150 ppm. Most mineral waters have at least 220 ppm total dissolved solids, and will have it listed on the bottle, which is why these test strips work in this case.If you need to test ph of low ionic strength waters, such as distilled, tap, most spring waters, then you'll probably need test drops or a meter instead. If you really want to try ph test strips for these waters, there are 2 things you can try. First, you can try soaking strip in water longer such as 30 to 60 seconds instead of 2 to 3 seconds. Second, and more effective, you can try dissolving a neutral salt to increase total dissolved solids. Potassium chloride KCl should work which you can purchase as a solution. Table salt, sodium chloride, should also work, but look for one that is plain salt without anti-caking ingredients and without iodine. Check the kosher salts wherever you buy groceries. Neutral salts won't change the ph of the water, but will increase total dissolved solids. Obviously don't drink the sample you test if you use this approach.
Recommended Products
