Your cart is empty.
Your cart is empty.Product Description
Leo B
2025-08-26 09:58:33
This pump has replaced a 7-year-old Hayward that seized up and tripped breakers. Like so many on here I was done with Hayward and sought this as an alternative. I chose this brand because of the reviews that mentioned excellent after-sales support. So far I haven't needed it. I had to redo the plumbing due to small dimensional differences between this one and the Hayward. This is more powerful than the Hayward, I can turn on my waterfall feature without dropping the pressure so much that I lose heat. The low speed setting will not raise the pressure enough to engage the heater. That is okay, my plan was to use it to keep the pool clean in the off season and save a bunch of energy doing it. The high setting makes a normal level of pump noise, the low setting is very quiet. I bought a dryer cord and outlet instead of hard-wiring it because of the awkward location of the pump motor. If I have a problem I will come back here and update this review. Note that it is possible to put the strainer basket into the pump housing backwards, so just pay attention where the hole in the basket is relative to the inlet pipe.
Steven Gutierrez
2025-08-20 14:20:32
Ordered this pump to replace an older setup. Easy to plumb in and rewire. The first pump I ordered developed a leak at the impeller shaft cover. The first pump took a few weeks to develop the leak. I ordered a second pump since the fittings already matched the plumbing. The impeller shaft leak started right away. I was able to return the 2nd pump easily. Amazon allowed me to return the first pump, but I missed the return window. I would not recommend this particular pump.
Rob
2025-06-18 14:00:30
My inground pool pump went bad and replaced it with this one. So far itΓ’β¬β’s working great. The flow and the power of pressure the jets are throwing back into the pool is a lot better than my last pump. Very quiet. And for me easy to wire up and re connect the PVC pipes. Working great no leaks. Great price for this unit also. Back to enjoying the pool for the summer. Thanks amazon
David
2025-06-09 14:42:06
My repair guy said 3-6k to get a new pump installed depending on which model I wanted. Hell no, so I got this one. The wiring diagram is crap and it doesn't have a connector for the middle prong on the cap that the second hot goes to. My old pump had the white wire in it but after a lot of research I found it was not needed so I removed it. I ended up with the ground being obvious and the red and black going to the two power points on the diagram. They did not put a nut for the one on the pump to attach or a clamp for the one on the switch in the lid. So far it is whisper quiet on low and still pretty quiet on high. The flow is excellent, but I still have to wait a while to say how it will be in time. For the whole setup costing me about 300 with pipes and glue I am happy with it as long as it lasts a few years.
Kindle Customer
2025-05-19 12:31:09
Pool companies can no longer sell single speed pumps. The variable speed start at about eight hundred plus installation. My pool guy quoted me thirteen hundred dollars for the pump and install. His price was not out of line considering the initial cost of the pump, labor and the incidentals he would have to supply. I bought this pump for less than three hundred dollars and did the installation myself with the invaluable help of my son in law. Took a while but we managed to get everything working just fine. So far, this pump has run like a champ and I saved about nine hundred dollars.
Marijane F.
2025-05-18 18:35:26
This is the second Pipopa Pool Pump I have purchased. The first was over a year ago and it quit shortly after it was installed. Pipopa immediately sent a replacement and asked that I return the original for engineering to examine to find the failure point. The replacement is a 2 1/2 HP dual speed pump that I am very pleased with and still running like a champ. It is quiet and just the right power to keep my large salt water pool clean and fresh. I purchased the second pump, a 2 HP dual voltage pump, for my father's house and have had two fittings break at the top pump housing between the threads. Again I contacted Pipopa Customer Service through Amazon and they were quick to respond sending 2 replacement fittings and assurance that their engineers would look at the breaks to see if the fitting design could be improved. These pumps are not terribly expensive and are a great value for the money. The fact that their customer service is so responsive is very refreshing and certainly an added value for the money. I would recommend these items to friends and family alike. Thank you Pipopa for your willingness to exceed my expectations.
David
2025-05-01 12:41:23
I have had issues wit this very early. Beginning with the fitting being brittle after little use and over a few months, the GPM decreased and is barely pumping water. It would take nearly 12-16 hours to cycle my entire 13,000 gal pool.
Customer
2025-04-20 17:42:55
I ordered this pump and seller was quick getting it to me. I installed it and managed to brake one of the fittings. Not sure if it was me or the fitting but I wrote the seller and he was very quick to send me a replacement fitting. Fast forward 3 months and another fitting broke and again the seller was very quick to send a replacement. The pump works well and at 1/5 the price pool guy wanted I still think it is a good deal. Wish the fitting was a little more robust though.I would buy from this Seller again!
Jack
2025-04-01 13:52:15
I try a few pumps to replace my old variable speed pump installed 12 years ago. So far so good. Especially the lower speed , so quiet but the skimmer still work well.The wire connect is super easy, but you need something not in the package, go home depot around $3.
Buy me a Pint
2025-03-22 10:23:56
I hesitated between 3 or 4 stars. I was able to wire this up myself, you need 10 gauge crimp on spade connectors, then it makes sense. It works well although I am having prime issues. It does prime itself but I have o-ring problems in either the lid or the connection to teh skimmer. It pulses because it loses prime. Invest in O-ring lube, it will help get the filter basket lid off and on easier and seal the possible prime leak there. The other issue is at the inlet, the pump body is two plastic extrusions welded together. Where the O-ring sits on the inlet there was a bump where the extrusions are misaligned. I was able to carefully file the bump down, now I need to use a very fine sand paper to smooth the file marks. I have 95% seal now and less surging. I have a similar leak on the outlet and I suspect the same thing, the two halves of the body are slightly misaligned. Despite this I quite like the two speed pump and with my little robot it cleans the pool very fast.
Customer
2025-02-03 16:52:43
Good produit
Maxime X.
2025-01-26 09:28:22
Remplacement de ma pompe de piscine
Georges Choiniere
2025-01-11 10:34:17
Tres difficile a primer la pompe
Recommended Products