Shopping Cart

Your cart is empty.

Your cart is empty.

PLINIUS PHF1000D car Audio Amplifier Monoblock Class D MOSFER 1000 watts RMS Remote Subwoofer Level Control

4.5 (6) Write Review
Free shipping on orders over $29.99

$69.99

$ 31 .99 $31.99

In Stock

1.Size:4x140 Watt Rms Class D 4 Channel


  • Car audio amplifier 1000 watts RMS at 1-ohm load (14.4v); 600 watts RMS at 2-ohm load (14.4v); 360 watts RMS at 4-ohm load (14.4v);
  • Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry
  • 1-4 Ohm Stable - Able to continuously power loads of 1-4 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to
  • Engineered to be the most efficient car monoblock amplifier in its class so that you can get the most out of your vehicle’s electrical system
  • MOSFET pulse width modulated power supply and proprietary heat dissipation design will ensure the amplifier for car subwoofers runs cool for even the most demanding playlists
  • DIMENSIONS: 8.5" x5.1"x2", WEIGHT: 4.41 lbs


Product Description

a+

Class-D Amplifier

MOS-FET PWM Power supply

1-4 Ohm Stable Load

12 dB/Octave - Variable Low Pass Filter

Hi/Low input level switches

Power/protect LED indicators

Nickel plated input and output connectors

1

Speaker terminals

Used to connect speaker cables to the amplifier. See the wiring configuration section for more details.

2

Power /protect LED

If the amplifier is operating normally, the GREEN LED will illuminate.

If the amplifier is in protection mode the RED LED will illuminate.

3

Fuse

Replace with only the same value ATC fuse.

4

Power terminals

Used to connect DC power to the amplifier. See the power connections section for more details.

5

Output

The RCA jacks allow for a low level CH1 and CH2 channel signal output Simply connect to a second amplifier unit using RCA type audio cableskeeping them away from power wiring wherever possible to reduce risk of noise.

6

Input

The RCA jacks allow for a low level CH1/2 channel signal input. Simply connect to the source unit using RCA type audio cables,keeping them away from power wiring wherever possible to reduce risk of noise.

7

Gain control

This control is used to match the input signal of the source to the amplifier. See the setup section for more details.

8

Phase adjust

This control is used to set the speaker output phase for the amplifier and is adjustable between 0° and 180°.

9

Low pass

Control for adjusting the lowpass filter frequency

10

Subsonic filter

This control is used to set the subsonic filter which is used to limit the very low frequency information passed to the subwoofer. The frequency is adiustable between 10Hz and 40Hz.

11

Bass Boost Control

This control is used to add bass boost to the amplifier when LPF is selected. The bass boost is adjustable between 0dB and 12dB

12

Remote input socket

Used to connect the remote level control to the amplifier.

amplifier

DIMENSIONS

8.5" x5.1"x2", WEIGHT: 4.41 lbs


Erick Hernández
2025-08-07 15:59:53
Recién compré este amplificador y lo conecté con dos subwoofer, un Kenwood de 12 pulgadas 200 rms a 4 ohms y un subwoofer JBL de 10 pulgadas 300 rms a 4 ohms.Puedo decir que el sonido es excelente y la reproducción de bajos profundos es insuperable.Estoy muy satisfecho.La alimentación la hice con una fuerte conmutada de 50 amperios 14 voltios, y la salida de señal la saco de un minicomponente SHARP CD G 1000.Este arreglo lo hice porque no pude conseguir el subwoofer original del minicomponente, pero la calidad es insuperable.
Randy Shriver
2025-05-15 10:02:56
The media could not be loaded.
Z Noble
2025-05-12 12:33:02
Had for a week or two now, seems to be good so far. I appreciate the clip light on the remote.
Great product
2025-03-21 12:01:19
If you only need 300-400 watts rms go for it. I actually swapped this with a power acoustik rzr1-2500d and it's so much better.Save your money and get something worth a damn of your on a buget with low wattage needs it will work.
Customs
2025-01-23 15:05:51
The PLINIUS PHF700D Car Audio Amplifier is an absolute beast! With 700 watts RMS, it delivers incredible power to my system, providing deep, rich bass that hits hard. The Class D MOSFET technology ensures that it's efficient and runs cool, even during long listening sessions. The remote subwoofer level control is a great feature, allowing me to easily adjust the bass to my liking. It's built to last, and the sound quality is top-notch. If you're looking to boost your car audio system with a reliable and powerful amplifier, this one is definitely worth every penny. Highly recommend!
Jeremy Barron
2024-11-13 16:10:27
The media could not be loaded.