Your cart is empty.
Your cart is empty.This is a pop-up ball joint rod that fits Ez-Flo and ProValue faucets. It comes in a 6-1/2 inch length and is easy to replace.
Cheryl
2025-09-04 16:53:36
Fit perfectly as original and easy to install. Works great.
J. Donch
2025-08-12 16:42:01
An exact replacement for a builder grade pop-up ball joint rod at a very affordable price. For the price of ONE at the local store, I can replace all 4 in my two, double lavatory sinks. The ball is 15mm/.59 inches and the rod projects 1.4 inches from the ball. Originally, like others have mentioned, I thought the rod was too long as it initially rubbed against the tail pipe. thinking I might have to cut/grind it down, upon taking it out again, I realized that when putting it on, the inside plastic seal had fallen off. Once replaced, it fits/operates perfectly. Note that it comes with TWO plastic seals. One should be placed on each side of the ball to seal and provide smooth operation of the ball.
M3 Pete
2025-08-07 11:14:57
Needed to replace a 15mm ball rod and this was a perfect fit. I took off a star because I wish these came in stainless steel, as these chrome plated steel ones rust out. But I'd buy it again.
Robert
2025-07-19 17:39:06
Wasn't a perfect replacement as far as the ball size but as long as the plastic pieces are set over the ball, there will be no leaks and it will work just fine. Overall happy because it sorted out my
Michael Morris
2025-07-14 11:27:29
Fit my sink perfectly! Nice Quality. Could not find this part at local big box (HD) store.
Dan
2025-07-07 17:15:50
This item got the job done and was super easy to install, my only complaint was the quality of the piece that's supposed to keep the bar locked in/to the pusher, it isn't the strongest and if you pull on it too hard it pops it off again.
Customer
2025-07-03 10:36:54
Perfect fit for my sink drain and works as it should!!
Dr. Zen
2025-06-14 13:13:41
The faucets were installed when my home was built over 10 years ago. It's been a while that it doesn't work as expected, whenever I pull the rod up to retain the water, it just doesn't stay there. I have been reminded to replace them (it's over 10 years after all), but that would be a lot of work, some money involved, and I am not that handy. Until I got this part! After I replacing this the faucet works just like what it was in the past. The washer and the ball and the rod crossing the ball were worn. Just a few dollars and less than 10 mins I think it will work for quite some years.By the way, I totally recommend everyone to buy a few extra in case the product is out of stock in the future given the price is so low (compared with new set of faucet).
Sim
2025-05-28 17:22:55
I like that it’s a standard size. Still does the work at such a little price.
Customer
2025-03-20 18:13:25
Cheap and works fine!
jeffree
2025-03-02 15:51:58
As you can see, the dia of the rod is little smaller than the original one, so is the pivot ball. But finally it seems working well with the two washers provided. Also I used the original plastic nut instead of the slim metal one. I fixed my lift rod with ~$7 so I am happy with it.
Debbie
2025-02-25 17:01:35
Works as intended, and easy to install to replace the original.
Edward W.
2025-02-08 15:33:47
Fits perfectly as replacement to our broken joint rod for the sink drain cover to lift up/down. Great as a replacement for repair purposes. I bought two just in case another sink drain decides to break apart (due to rust, they actually can break apart/rot/rust out.
Recommended Products
