Your cart is empty.
Your cart is empty. Note:Please make sure that the remote controller have a 3CH function button.Otherwise it does not work.
Compatible with HSP Traxxas Tamiya CC01 4WD Axial SCX10 1/10 1/8 RC Car Truck Crawler.
After connect to the receiver third channel(CH3), you can control the light freely.
Small size and lightweight, it won't add extra burden on RC car.
Replacement parts for rc rock crawlers,and is a good choice for RC car fans.
Material: Metal, Plastic
Powered by: Battery
Input: 5-12.4V/1A
Type: Functional Switch(On/Off, Breath mode, Flash mode)
Wire Length: Approx. 22cm/ 8.66inch
It can connect 4 set led lights,there are 1.2.3.4 number on the control panel.1 and 2 are in parallel relationship,3 and 4 are in parallel relationship. It can be understood that the output lamp group is 2 groups and 4 ports.
Each time the 3 channel switch is toggled or pressed, the cycle changes:
When power supply on, 1 & 2 , 3 & 4 light off →→ 1 & 2 to light up, 3 & 4 light off →→ 1 & 2 to light off, 3 & 4 light up →→ 1 & 2 to light up, 3 & 4 light up →→ All light breathing mode open →→ All light breathing mode open →→ All light flashing mode open →→ 1 & 2, 3 & 4 are light off....cycle.
Package includes:
1 * RC CH3 LED Light Lamp Control Panel
Merinda
2025-09-01 15:28:00
So many people on here (bless ‘em) saying it doesn’t work, plug it in right😂!!!!! don’t plug the light side in hORIZONTALLY! Plug it in VERTICALLY!! And whaaaa-lahhhh! Think about the diagram picture in the ads photos, makes sense right!! Have fun!!!
Timothy Osborne
2025-08-20 14:23:13
The media could not be loaded.
Andy Watters
2025-08-01 10:36:37
So far I'm not impressed. I have tried plugging this in every which way and nothing happens. I have verified all of my wiring is correct. Hopefully the replacement will actually work.
Adam Swint
2025-07-11 10:56:51
This is exactly what I've been looking for! I wanted to be able to remotely manage my lights and have multiple options, and this controller provides! Setting up my TX was dead simple, and now I have complete control of my body lights and roof rack lights completely independent of each other.The controller has 2 channels, with 2 ports each, so you can output to 4 separate light sources, and have each of the 2 channels work independently of each other.All in all it works really well and it's one of the best supporting mods for anyone running a bunch of LEDs without an active controller.
James Morrow
2025-07-02 14:38:09
It does need instructions, but easy enough to figure out
Dan Cotto
2025-06-19 11:09:33
Must have if you want to control the lights on your RC and it gives multiple light modes
Michael Tallis
2025-06-11 17:36:51
Switch two different loads on/off or have them all on/off, strobe flashing, or breathe mode which is a slow fade in and out. After I made my connections and tested, I used 3/4" heat shrink tubing to seal it up.
Corey S.
2025-04-22 09:38:23
The media could not be loaded.
peter
2025-03-27 10:51:05
Added this switch to control lights on my r/c , worked as promised , watch the polarity at the connection to the receiver though as it can be inserted either way i think
Devin
2025-02-01 16:02:57
Doesn’t work following the labels in the pic, even swapping all plugs around to every possibility it doesnt work at all. Doesn’t even let power through it
FCC
2024-11-18 10:14:28
might not recommend this product
Recommended Products
