Your cart is empty.
Your cart is empty.
100%brand new and high quality.
Features:
Fit for AXIAL SCX10-iii AXI03007 1/10th scale RC crawler car.
Made of high quality material,Durable and easy to install.
It can replace the front/rear bumper mounting base,and offer a stand for the car servo.
Specifications:
Part name:Front and Rear bumper mount
Material: Aluminium Alloy
Color:Black
Package Include:
1 Set x Front and Rear Servo Stand
Dmmt Dave
2025-09-02 15:25:51
Took a chance on these, being half the price of other bumper mounts for my scx10.3 had me a little cautious. One screw was a bit tight going in on the front top, but other than that fitment was great and the quality feels pretty good, especially for the cost
Logs
2025-08-20 13:50:49
Solid piece light but made the truck stiffer
Customer
2025-08-10 15:15:19
They have a good appearance. There quality is nice . They fit right up to the scx10III. Super ease of installation. There performance is what you would expect from a bumper holder.
AddictedToPurple
2025-07-29 13:25:31
The good:The brackets fit the frame rails (stock Axial frame) great, and the bumpers (Injora, front and rear, with a winch on the front, so it's heavy) fit into them perfectly. There's nearly zero flex between the bumpers and everything now, even when I get lazy and pick the truck up by the front bumper's stinger. The rear bracket fit between the rails better than the front, and the bumper fit into the bracket just as well, but then we get to...The bad:While all the hardware is included, I had a problem with two screws, or two holes, depending on perspective. The front bracket had zero problems, went together like it was a factory Axial part. The rear fit the frame perfectly, but the holes for the screw/pin thingies that hold the bumper in position needed two attempts, with excessively long shipping times for both, before I had to dig through my hardware bins for the right size. The included screws are M3.5 or M4, and the holes in the bracket are M3. I had decided to just use set screws and hope nothing lets go, but then I ran across two M3 screw/pin thingies that fit perfectly. They're the ones that go through the axles and hexes:Axial - AXI236172 Screw Shaft M3 x 2.0 x 12mm (10 per package, you'll need two)Overall, I'm happy with them, despite the frustration. If the hardware was correct, five stars. I can't comment on how well the stock body mounts will interact with them, as I have a set of Fine Laser Designs clipless mounts. It's a little more difficult to get the rear to lock down with the FLD mounts, but a little filing will fix that, and it's still better than dealing with the stock hidden body clip setup.
Svein Gulbrandsen
2025-07-04 10:26:21
Nice ithem.Arrived earlyer than exspected
Marv
2025-06-20 16:24:04
Fit my Axial SCX10 III great, added a lot of rigidity to bumpers. Pairs great with some aftermarket metal bumpers.
Jordan C
2025-04-20 14:56:03
They fit good on my scx10 III base camp
Derek D.
2025-03-26 21:22:06
Does not fit as described, had to modify to fit truck
José Alfonso López Nieto
2025-03-17 18:20:47
Buenos acabados, quedo perfecto en axial scx10iii
Karl Haipee
2025-03-14 15:15:55
Looks and feels good but not suitable for the axial 10.3 gladiator as it’s too short I was able to use the front mount which improved the rigidity so theres that over all good but on my end I didn’t see if it was compatible with the gladiator
Fabrice2801
2025-03-04 20:46:42
Fonction pour le devant pour le Jeep GladiatorMais pas pour l'arrière trop court!!!
SouPNaZi
2024-12-10 15:57:38
The front mounts no problem. The rear is another story. It's off by around 1/32nd of an inch or a few mm. Chassis mount hole and bumper screw holes don't align. I may be able to grind the meat of the mount to allow it to go into the chassis farther to line up but wtf. I shouldn't have to.
Recommended Products
