Basic operation:

1. Press the button to restore factory settings:

When the circuit board is powered on, keep pressing the "setting key" on the circuit board for more than 10 seconds, you can see that the red indicator light on the control board lights up and the fingerprint module starts to light up in white. At this time, release the "setting key", and if the green light of fingerprint module is on for 1 second, it means the deletion is successful; if the red light of the fingerprint module is on for 1 second, it means the deletion has failed. After restoring the factory state, the system will clear all fingerprint libraries. At this time, the system is in demonstration mode, and any fingerprint can control the relay to open.

2. Recording the fingerprint of the administrator for the first time: [Maximum number of administrators is 10]

When the system is in the factory state, press any finger on the fingerprint window and hold it for about 5 seconds without letting go. The yellow light of the fingerprint module will light up. After the finger is removed, the yellow light will flash, and the operation of adding the administrator fingerprint will be entered. The light blue light is on after the finger is pressed, and the yellow light flashes when the finger is lifted. Press the finger 4 times continuously, the green light will be on for about 1 second, and the new fingerprint entry is successful; if the red light is on, it means the entry has failed. The yellow light continues to flash, you can continue to enroll more fingerprints, if you need to end the enrollment, about 5 seconds without any operation will automatically exit. It is best to record a few more fingerprints for the first time to record the administrator's fingerprints, which is convenient for future use. The fingerprints that have already been registered are not allowed to be re-entered, the red light will be on, and the registration will be automatically exited.

Enter more administrator fingerprints:

You must use the administrator's fingerprint to press for more than 5 seconds and not release it until the yellow light turns on. After removing the finger, the yellow light flashes and enters the operation of adding fingerprint management. The entry process is the same as above.

3. Enter the fingerprints of ordinary users:

You must use the management fingerprint to press for more than 10 seconds without releasing it. The yellow light turns on in turn, and the pink light turns on and then removes your finger. The pink light starts to flash, and enters the operation of adding ordinary user fingerprints. The entry process is the same as above.

4. Delete all fingerprints:

You must press the administrator's fingerprint for more than 15 seconds without releasing it. The yellow light turns on and the pink light turns on. After the yellow light turns on for the second time, remove your finger and the yellow light flashes to enter the operation of deleting all fingerprints. At this time, press it again with any finger, the green light will be on for about 3 seconds, and all fingerprints have been deleted successfully. At this time, the system is restored to the factory settings, and any fingerprint can turn on the relay.

5. Delete all common user fingerprints:

You must press the administrator's fingerprint for more than 20 seconds without releasing it. The yellow light turns on, the pink light turns on, the second yellow light turns on, and the second time the pink light turns on, release your finger, and the pink light flashes to enter the operation to delete all ordinary user fingerprints. . At this time, press it again with any finger, the green light will be on for about 3 seconds, all ordinary user fingerprints have been deleted successfully, and the management fingerprints are still available at this time.

6. Mode selection: [factory default is mode 7]

When the circuit board is powered on, press the "set button" on the circuit board, the blue light on the circuit board will flash, and the number of flashes represents different relay output modes. After pressing the button again, the number of flashes will cycle from 1 to 10. The set mode will be automatically saved.

Relay mode 1 (used in car door switch 1): The blue light flashes once.

After the fingerprint is successfully unlocked, relay 1 is turned on, and after 0.6 seconds, relay 1 is turned off.

When fingerprint unlocking fails, relay 2 is turned on, and after 0.6 seconds, relay 2 is turned off.

Relay mode 2 (self-locking mode): The blue light flashes twice.

After the fingerprint is successfully unlocked, the relay 1 is turned on; after the unlock is successful again, the relay 1 is turned off.

If fingerprint unlocking fails, relay 2 is turned on, and after unlocking fails again, relay 2 is turned off.

Relay mode 3 (jog mode): The blue light flashes three times.

The administrator's fingerprint is successfully unlocked, relay 1 is turned on, and after 0.6 seconds, relay 1 is turned off.

Normal user fingerprint unlock successfully, relay 2 is turned on, after 0.6 seconds, relay 2 is turned off.