Your cart is empty.
Your cart is empty.Product Description
Control the Horn
This hand horn switch is mainly used to control the horn on the handlebar of the motorcycle, which is convenient for the driver to remind passers-by and ensure safe riding.
PRODUCT DETAILS
Front View
Material: Plastic ; Cable Length: 75cm/29.5 inches ; Handlebar Modes: 22mm.
Back View
This handle is sealed with a rubber sleeve around the horn switch.
Side View
Applicable Handlebars: This motorcycle handlebar horn switch is suitable for installation with a handlebar length of 22mm (7/8 inches)
Applicable Handlebars
This motorcycle handlebar horn switch is suitable for installation with a handlebar length of 22mm (7/8 inches)
Specification
Universal Cable Length: The length of this handle horn switch cable is 75cm/29.5 inches, which can meet the installation requirements of most motorcycle models
edgar
2025-08-29 14:01:47
Worked great for my kid's dirtbike. Our dog chewed up the original ignition so I ordered this for a kill switch. I just unplugged what was left of the old one, plugged this one in and it was good to go.It also got here the next day after ordering it.
Brad460
2025-08-22 11:56:05
Installed on my 2000 CR125- worked perfectly and looks nice.
Skitter
2025-08-17 19:51:23
Had a bit of a startle out on my kayak with a fast-moving boat that didn’t see me. Made the decision to rig up a horn on my yak and this button worked perfectly for it. The button fit on the bars of my kayak seat… I connected the wires to a quick connect/disconnect pigtail that pugs into a 12v power box I made. The wires are adequate for my application but I took a star off because the solder connection inside the unit is pretty minimal. I added more and then sealed the solder joints in epoxy resin to stabilize and weatherize the assembly. The horn is mounted in the bow. Boy howdy do the inattentive boaters/wave runners pay attention now!
Vincent Barrios
2025-08-16 20:22:23
Needed a new kill switch I ordered this one and figured it was plug and play for me but ended up having to cut the wires (removed that white adapter on the end) and connected it to the wires that were attached to the power and ground wires after doing so it worked great.
Laird
2025-07-22 16:16:23
Needed a minimalistic horn switch for my scoot, cheap and works!
Dick Guthery
2025-06-29 14:14:56
Great switch and small enough to place in limited space on handlebar’s. Easy enough for me to install, but some instructions for others could be included. Works great on our flat rack race bikes.
Mario Orsini
2025-06-24 11:46:35
I originally installed one on my son's old race bike and now my pit bike, a Honda CRF50. The one on there had broken. This one works great and is much higher quality. It's held up great so far. I like it so much, I ordered another to put on my CRF100.
David R.
2025-06-22 20:43:32
I'm using this as a start switch on a CRF230 to replace the big oem unit. It plugs directly into the factory harness. The picture shows the bottom of the button which is just open....not sure how long that will last exposed to the elements. I put some electrical tape over the bottom to help shield it from dust and water. We'll see how long it lasts, I'll follow up this review after some time using this unit.
Christian Racine
2025-05-29 18:01:08
Does what it’s suppose to do!
Customer
2025-04-17 18:25:46
Great product, easy to install, and fast shipping
rodney
2025-03-18 18:19:26
Works as it should
kenorawalleye
2025-03-15 17:10:38
Cheap, but works
justin deroy
2025-02-16 12:39:32
Good product super slow shipping
Recommended Products