Your cart is empty.
Your cart is empty.Product Description
Jurica Brown
2025-09-05 16:05:53
The product works. Installation was easy to install. Cost-efficient compared to other sites' listed prices. I am a satisfied customer.
RestlessinPhoenix
2025-07-09 12:05:47
I was hesitant buying a non OEM burner replacement as other listing had bad reviews or complaints that terminals weren't the same.My Ge large burner would only heat the outer ring.I could see the old burner had an issue with the filaments so I knew i just couldn't fix it.I bought this and installed it in about 20 mins. It includes a terminal adapter wire as one of the terminals didn't match oem wires. The jumper wire was a little loose so I did have to crimp it.The holes that match up to the clips were slightly off but I still managed to get it locked down.Fit is perfect. Heats quickly and now I have the small and large burners back.Compared to buying oem at almost triple the cost...this is a great alternative.
Alex Ovalles
2025-06-24 14:29:52
Excellent product easy to install.. Good presentation and product protection..
rick m.
2025-06-15 11:01:58
Slightly different hook up but works fine on my stove
scarter1674
2025-05-25 11:15:57
Easy to install and works great.
Sonnymig1
2025-05-15 19:14:56
Installed on GE oven at a fraction of the OEM cost. working very well for 1 week so far and got us through the Christmas cooking. Will monitor and respond back if any changes occur.Installation was quick and easy. recommend watching videos for first timers. Check wires that plug into heating element. I had one wire that was over heating and needed the lug replaced due to over current from original bad element.
nozama
2025-05-14 17:17:43
I found this Haliant Element from this vendor and very happy about the purchase. Will see the longevity of the new Haliant element. The original one lasted just 6 years with very lightly use since we use air fryer more than stove.To replace the element, important to "turn the circuit breaker off" and check the clock display is OFF from on.1) Remove two screws on side of the control panel (have to pull the whole oven body out)2) Remove the panel without removing the display and knobs.3) Remove 7 black screws and lift the glass top to access the burner elementThe original wire clamp width is small and thinner on the element unit but the replacement element has two identical male clamps. The issue can easily resolved by using provided adapter cable with proper clamp sizes (please refer to picture)
Eric
2025-04-20 21:57:42
Fits perfectly for my glass stove top. GE stove model JB655SK3SS.
Carlos A.
2025-04-19 10:50:22
Funciona a la perfección y ya llevo un mes usándola
keith
2025-04-04 10:47:08
Save the appliance repair bill. diy. Easy replacement and great instructions. 10 minutes and done
Frankie
2025-03-15 18:34:17
It took only 45 minutes from start to finish. Make sure take a photo of the wiring. Work well likes new.
DQ
2025-02-05 13:33:30
one leg is little different with the original one and my husband has to cut it with machine to install itbut finally fix our stove and really saved us the money
Customer
2024-12-12 16:38:40
Perfect match for my 8 year old GE range and way cheaper by 2/3rd than getting a repair person in. Quite easy to replace requiring 4 screws to access the element (2 screw to access element; 2 screws that clip the element to the glass surface). Would recommend that 2 persons perform the swap because of the clips holding the element are a bit ackward to replace. Cannot vouch for the longevity of the replacement element but it worked perfectly upon replacement including resetting of the “hot†light which functions again (was a constant red to give a visual cue that the original element was kaput).
Recommended Products