Your cart is empty.
Your cart is empty.Product Description
For M6 & 1/4”-20
Vgate 8-Way Battery Terminal Distribution Block
8 AWG up to 4/0(XL) AWG Gauge for Lithium or AGM Lead Acid Battery with Bolt Down Ends or Threaded Studs
Product Details - O8-M6 (M6 & 1/4”-20)
4 x Hole Holders
- Vgate battery terminal 4 x Hole Holders exactly to hold
2 AWG to 1/0 AWG (2 Holes) and
1/0 AWG to 2/0 AWG (2 Holes) welding cable.
4 x Threaded Studs
- 4 x Threaded Studs to connect ring terminals (cable lugs);
- Include the Following Stud Sizes:
8 mm studs (4)
Compact Size
- L x W x H: 2.95 x 1.77 x 0.63 inches
- The mentioned ring terminals (cable lugs)are suitable for crimping 4/0(XL) AWG, 2/0AWG, 1/0AWG, 8AWG cables, etc.
Parts for M6 & 1/4”-20
- Parts Included:
Bolt (Inch and mm 2pcs/each),
Nut (Inch and mm 2pcs/each),
Flat (8pcs) & Spring (2pcs) Washer
Design Details - O8-M6 (M6 & 1/4”-20)
- Vgate 8-Way Battery Terminal Connectors: M6 or 1/4”-20
- 4 Input Hole Holders & 4 Threaded Studs
Installation Process
Step 1
- Choose correct size of bolt and nut (mm or inch due to difference on thread spacing).
Step 2
- Screw down studs to bolt down end battery (Please keep length of stud enough to tighten down terminal).
Step 3
- Then put flat washer first, if mounting base size is too small (It’s necessary, or can not tighten down terminal).
- Also For Threaded Studs Battery.
Step 4
- Continue to put terminal, flat washer, spring washer one by one, then tighten down nut.
- To increase or decrease flat washer to tighten down terminal.
O8-M6 (M6 & 1/4”-20) Battery Terminal
Important Installation Tip
- For proper installation, please follow the accessory setup shown in the image. Make sure all parts are securely tightened.
Berry
2025-08-08 13:41:35
Good value and worked perfectly did have to modify it and drill out the hole because I wasn't sure of the stud size
Nikko Soriano
2025-06-25 15:40:20
Has many spots for wires to run to and very compact. Not very heavy, but also very sturdy.
The rock
2025-05-11 10:53:21
I like the quality of material the bolt hole was just too small for a gm side post battery bolt
wyatt
2025-05-10 14:24:14
Fit perfect
Jorge V.
2025-03-12 15:47:59
These are beautiful polished battery terminals. They work as described, easy to install and holds multiple battery cables securely.
Gilbert T.
2025-02-17 17:35:42
Probably not going to use this because it doesn’t tighten very well
Toby Martinez
2025-01-18 12:54:09
Vgate 8 way battery terminals do a veruy good job keeping my battery area nice and neat without all kinds of wires running everywhere..... easily connects to most kinds of batteries and makes connecting accessories like amplifiers and light kits alot easier.... very durable connection points and hardware to secure the wires and insure good power and ground connections
Customer
2025-01-03 18:21:25
This review is for Vgate 8-Way Battery Terminal Connectors for Lithium or AGM Lead-Acid Battery with Bolt Down Ends 6mm or 1/4"This item consists of very nicely machined positive and negative terminals that are intended to attach directly to a threaded hole on the battery itself or to a military style battery post adapter. Each terminal has four large diameter holes with threaded studs that will securely lock down cables inserted in the holes. It should be noted that for best contact, a ferrule on the end of the wire might be needed for smaller cables. There is a lot of extra hardware provided to facilitate connection to the battery. Most of the hardware and grub screws for securing the cables are mildly magnetic, indicating some type of stainless steel.The terminals have a polished appearance and will enhance the neatness of wiring connected to the battery. This is a far better way of connecting multiple conductors than using ring terminals con the battery terminal clamps, especially for large diameter cables.Overall, a well made, robust design that should provide long service. This allows installations to be much neater and thus more reliable. Recommended.
Recommended Products