Your cart is empty.
Your cart is empty.Product Description
Vertical or Horizontal Mounting
Extending Wall/Ceiling Projector Mount
Enhance your visual setup with the heavy-duty, all-steel, universal wall/ceiling projector mount! Ideal for any home or office, this high-grade steel mount is weight tested at 44 lbs and designed with height adjustment and adjustable arms to fit most projector brands with mounting ranges from 8.9" to 12.4". Available in Black or White
Designed for 8.9" to 12.4" Hole Spacing
4 Hole Pattern
3 Hole Pattern
Internal Cable Management
Keeps cables neatly routed through the the arm for a clean setup.
Raj Srinivasan
2025-09-02 09:02:33
Got it for my Optima HD65 and worked out well as wall mount. May not fit directly. I had to use only two mounts to fit the triangle holes on the projector base. The trick is to use left side mount on back of the projector and right side we need to use the short mount bracket and long bracket together to align the triangle .. front two mount brackets will just be left parallel to front of projector to support the base. Since I am mounting the projector upside down the arm ends at the projector from nicely and thus fitting the projector within the base arm length and I don’t need to extend.Aligning to the screen is a bit of task. As the lens is placed to end in this projector .. get the center right to some accuracy by placing projector normally first on night stand and table and get the center on screen with plumb line and then have it wall mounted .. I used toggle bolts to secure the wall bracket instead of the ones provided as my placement falls between two studs.. would recommend this quality one and finish is perfect
Emmaly
2025-08-29 21:12:28
There's no problem here. The mounting is very flexible in how you can use it, so you've got choices and it works well for projectors with various mounting holes in many orientations and placements.
Cathryn Massing
2025-08-02 14:43:40
Overall I really liked the product.My only complaint was in the setup. The instructions were pretty good overall, the main issue was in the packaging. There was a significant amount of hardware (some necessary and some unnecessary depending on your projector model) all together in a single bag. Particularly five unique types of screws and six unique types of washers, some of which look very similar and can be difficult to distinguish between during setup (especially when they all come together in one big pile).The package contents page was of little help in identifying which washers were which. The instructions would simply state "and washers (M-J)" leaving you to sift through the pile of washers and begin comparing them all to each other. By looking at quantity, dimensions, and which screws are used with each washer, you can ultimately figure it out without too much of a headache. I have attached a photo to this review showing each correct piece to the right of its picture. Hopefully this will help people identify things more easily.I only wish the hardware had come in separate labled bags to reduce frustration and speed up setup. I was also missing one of the six (M-A) screws I needed. I emptied the contents of the bag into a tray and took inventory immediately so I know I never received it. Additionally, there are three screw options included depending on what your projector requires. I found the right thread diameter for my projector, but the screws were a bit too short so I had to make a run to the hardware store and get longer ones. It works great now.I've attached a picture of the mount just after finishing setup (I'll perform cord management later), and it works exactly like I hoped it would. The fact that I gave this mount four stars despite the frustration during setup speaks to how much I really liked it once it was all finished. Post-setup it is a five star mount in my book. The wall/ceiling option is handy, the arms on the mount adjusted well to line up with the threading on my projector, and the swivel/tilt was wonderful as well. It does everything I need it to do, perfectly.
gtrman1263
2025-07-09 17:58:47
The one negative I have to bring up. There are lots and lots of screws and washers. And they are not labeled or separated into bags that tell you which ones go where. So you have to correlate between the parts list and the instructions and what you actually have sitting in front of you. If you're intimidated by stuff like that this probably isn't for you. But I'm guessing all these basically assemble the same. I had a somewhat unique problem as the place I wanted to mount my projector is right above my TV. Then the projector screen is on the opposite wall. My room has an angle on that wall because of the roof. So I basically just screwed this into the stud going across. But if you were to want to wall mount this and felt insecure about it you could always attach a board across two studs and then mount it to that.Anyway, as a result of my unique placement problems I also needed to flip the mount upside down so the projector sat on top. I was somewhat worried that this was going to work out. But in the end it worked perfectly. You just have to tighten up everything enough to where the projector doesn't fall over when you run it on the top. Effective product holds the projector securely
Jimmy
2025-06-18 18:12:13
Great mount, good build quality but for anyone getting this to mount a projector to a wall, the only hardware they include for wall mounting is hardware meant for concrete/brick walls. So of you're wanting to mount it to drywall, you will need to purchase your own drywall appropriate hardware.
John
2025-06-04 13:43:18
Okay--simple installation for starters. I used the wall mount option, to the side of the room, at an angle from the projection screen. Very out of the way.There are a couple of bolts to tighten that require a 10 mm or so flat end wrench which is not provided. Every other bolt or screw is hex key (provided) except the wall mount screws.Once everything is tightened it is completely solid. I read some complaints about wobble and I suspect it's because of those two bolts that require a flat end wrench to tighten.And that's what I love about it--set it up once, forget about re-centering or focusing ever again. My projector had good manual keystone corrections, which allowed me to adjust the picture perfectly once I got some coarse location using the projector bolts and screws. If you're going for a wall mount from the side of the room, be sure you have keystone functionality.
B
2025-05-27 12:59:06
As other customers have stated, the mounting bracket is too far apart for wood studs.
David
2025-05-26 12:33:55
Really easy to install, fit perfect with my projector so thanks a lot, 100 percent recommend!
Francisco R.
2025-04-26 14:24:14
Excelente calidad de los materiales, pintura de buen espesor, los soportes se pueden adaptar básicamente a cualquier proyector de diferentes medidas, cuenta con los aditamentos necesarios para una instalación cómoda.
E.Z
2025-03-08 17:34:48
Solid and very adjustable. Must be installed according to your projector's throw distance, which is a pain as you have to be sure before drilling holes in the wall or ceiling, but that's with any permanrnt mounting system. If you want to mount it in drywall, you must get anchors and screws from your local hardware store as this kit doesn't include those. The screws provided are for concrete/cement. Anyone complaining about this must understand that your setup is custom. There's nothing wrong with this mount, tighten your screws properly and that's all! Great mount.
Customer
2025-02-03 20:24:05
Very Good product
Chloe
2025-01-27 15:35:32
Very sturdy and stable. Works great and was easy to install
Recommended Products