Your cart is empty.
Your cart is empty.Product Description
Pre-soldered wire
What you receive is a pre-soldered toggle switch,full of solder joints that won't fall off even if you pull hard, and a black heat shrink tubing that wraps it completely for a very professional look.
Silver Contacts
The internal contacts have been completely upgraded to silver contacts, which have better contact and conductivity than copper contacts and, importantly, do not oxidize.
More gadgets
Two nuts, one regular spacer, one anti-loosening tight spacer, and a small red cap
About Cable
A 20AWG pure copper red and black parallel wire, 300MM length makes you wiring more flexible.
Small size
Tiny size, it's easy to install even if you only have a small space, and of course it looks sturdy.
Installation
Just need to drill a small hole with a Φ6mm drill, put it in and screw on the nut, and connect the wires.
Andrew
2025-06-20 13:08:43
I had to take out some fancy fuel, injected, carburetion system that my chainsaws had, and go back to a straight carburetor. In doing, so I also lost the ability to kill the motor. I added these easy to install switches with no problem by drilling, one hole and connecting the wires now the chainsaw works perfectlAnd the switch is in a much easier location for me to remember.
GizmoGuy 777
2025-06-02 14:54:12
I don't like to write reviews and I don't do many, but I am really impressed with the quality control on these switches. For the price it is an outstanding value. I have purchased and put into use 70 of these switches, without a single failure. They ALL have all the correct mounting nuts, star and rotational lock washers. The ALL have the same length wires. They ALL have heat shrink on the wire solder point. I made an assembly of them to use on a mockup for developing the program for a PLC. Because I was expecting that there would be a bad one here or there, I tested a couple before I made the assembly and wired it up and those I tested worked. So I decided to put the whole thing together and wire it up and then change out any that were a problem. Out of 70 switches, THERE WERE NO PROBLEMS! I am impressed and I would recommend these.
K. Keller
2025-05-30 13:01:07
I used them for making small laser pointers to switch the 3V DC. The wires are substantial enough for easy soldering or crimping. A solid snap on/off too. The red toggle is actually a rubber cap/sleeve over the switch handle, and can be removed if you prefer the smaller silver handle under it.
Hemy03
2025-05-03 11:08:38
Most worked well but 2 fell apart the 1st few clicks.
Customer
2025-04-26 21:31:42
good switch
john
2025-04-25 12:39:28
Good quality switches.
Calvin
2025-04-08 15:40:35
I used these on my On18 train layout to control the power going on/off to a rail so I could isolate tracks. If you want to isolate both rails/run multiple trains, you will need a different switch style. Spending a little extra to have them pre-wired is a huge time savings for me and I feel is well worth the investment.
amazon4jose
2025-04-07 17:20:37
I use the to teach basic electronics. It Does what it’s supposed to do. Gets the job done.
Colin Langley
2025-02-28 14:34:40
Great quality toggle switch.. I'm using these for my model engine's for ignition on.. nicely packaged and Great value.. I will definitely re-order for sure thanks.
Jürgen Matzke
2025-02-22 13:25:28
Schnelle Lieferung,gute Qualität, Preis passt, immer wieder gerne
Manolito
2025-01-25 17:17:46
Excellent, neat, quality product.
Massimo Romoli
2024-12-28 14:00:07
Sono ottimi e funzionali.
kia sportage108
2024-12-14 16:24:20
Calidad, funcionamiento y rapidez para la entrega
Recommended Products