Your cart is empty.
Your cart is empty.Product Description
Klaudio
2025-09-01 17:31:36
Very easy to assemble. Holds my printer, table top sewing machine and laptop with no problem. Has wheels that easily can move around when cleaning.It looks great! I would highly recommend this shelf!
Tsab
2025-08-10 19:16:30
This wasn't heavy, very easy to put together, very sturdy. Looks great!! And able to handle a heavy laser printer!
Brian
2025-07-15 16:30:50
Printer stand is great, execpt for the rinky dink wheels included. Either use the included feet, or buy 8mm wheels to replace them. The ones included broke within a week.Ordered replacement wheels, and the plastic inserts that hold the wheels in place deformed and broke. Ordering metal inserts instead.
TIMOTHY N.
2025-06-22 10:02:30
The box was heavy, so be careful!I received the 23.62"W x 18.89"D x 27.55"H size, but kept going back and forth on if I should have gone with the larger size. This one was a perfect fit!The metal parts are hollow, so they are light.The wood panels are well-built and sturdy.I was lucky enough to not have scrapes, or damaged corners on this item (like I had with others).I LOVE the way the screw holes use plastic expanding sleeves instead of just being threaded (this helps to keep the pre-fab boards from stripping out, etc.)I originally got this stand for my new Epson ST-C8000 for home office. The printer is at the right height for me and fit perfectly on the top shelf.Then I got thinking!I took out the middle shelf (for my taste it is too wide - a nice design would allow for a half-shelf there instead. But, this would call for a total redesign on the item). I then took the two bars off the shelf and put them on the rear for more stability.Why?Because I wanted to see if my 3D printer would fit - and without the shelf, it does! Even with the cover, but barely - this is where the larger sized shelf would have been nicer (but I can purchase one of those later once I have my home office finished being renovated).This smaller shelf allows for a huge printer on top (3D printer / Epson ST-C8000 / etc.) and if you have the adjustable center shelf in place, you can store paper, toner, filament, etc. Feel free to keep the middle shelf out and use the bars to secure the back as I did, and now you can put a printer on top and have plenty of room for a second printer on bottom.I also opted to not use the rollers as my basement floor is sloped for water drainage (my home was built in the 50s). The feet are decent, but maybe a bit small for the weight I have on top. I had a set of large foot pads from another project, and those just happened to fit. And, they can handle the weight I am putting on this shelf.All-in-all : LOVE IT! I'm not really sure about the price point just yet. Others offer the same item for less and yet others are more expensive - so this particular vendor is selling them in between the two prices I've seen for the same item. As I said before, I will definitely be buying the larger one as well once I have my office redone - and both 3D Printers will go on that one (and the enclosure I have will also fit for that one as well.)NOW: The ONLY issue I had with this item - see image. QA missed a punch hole in one of the bars - easy enough to hit out and keep going). ALSO, be careful to not overtighten the through bolts on the bars - as they are hollow, you could deform them (squishing them).
Customer J
2025-05-24 11:14:31
I needed a cart for my large printer, and this one was perfect. It's sturdy, easy to assemble, and has adjustable shelves. The included tools and well-labeled parts made assembly a breeze. However, the plastic casters aren't great for frequent movement. Despite this, it's an excellent addition to my home office, keeping everything organized and freeing up desk space. Highly recommended for its quality and functionality, though better wheels would be a nice upgrade.
Ron F
2025-05-07 11:26:40
So, there was only 1 thing I didn't like about this and I will mention it at the end.The positives were:* Easy to assemble. Took my time, took me about an hour. I could have done it sooner, but I was taking my time and also watching TV.* Instructions were actually good. Pictures were accurate, good sized, didn't try to cram too much into 1 picture.* All tools you will need come with (screwdriver, allen wrench, funky little hex nut tightner)* Extra parts for each piece screwing in except for wheels/"feet"* Choice between wheels/rollers or flat "feet". Both included. You choose.* All parts well labeled.* Screw holes in bars were well done. I've had some before that have been "off center" or problematic. These allowed entry very easily, weren't loose, etc. Made assembly easy and slick.* Middle shelf adjustable. I kind of wanted to adjust it low so I could put my AIO on the middle shelf...more stability and protection, and I still may, but it will make it more of a PITA to life the top of my AIO for scanning. I'll play around with it but the point for this bullet is that it is a nice thing to have that choice.* Height is about 8" more than previous unit I used. For some, this may not matter, but for me, it will be less bending over for my back.Note: Make sure when putting on the wheels/rollers that you put the 2 with the "brake" tab at the same end. Front or back, your choice, but should be paired together as front or back and not 1 each. I didn't notice anything about that in the instructions. No issues if you are using the flat feet.Now, the ONE thing that I didn't like...* The hex nut tightener...when you are putting the wheels on, I had to use my fingers to get them almost all the way screwed in and then use the tightener. Reason was that it just kept slipping off when trying to use it before that. If you have small hands that can't cup over the wheel and still able to use 2 fingers to tighten it until you get it to the last point and can use the tool, you will have to likely use 2 fingers from the side (I used 1 from each hand to make it easier). Takes some time and is frustrating that that was the last step and the only PITA part of putting it together.
M. Naz
2025-02-24 10:31:21
This has been great to have in my craft room. It currently holds my laser machine and is so stable. It was very easy to put together and is so versatile. It rolls smoothly with no issues and can easily be stored.
Stephanie
2025-01-26 20:37:00
This printer stand was super easy to assemble. However, I don’t use it for its intended purpose. I use it to store items within my room. It has lots of room and I love that it rolls so I can move items where I need them to go. Seems very sturdy and durable.
Recommended Products