Your cart is empty.
Your cart is empty.Yonico rail and stile router bit set (12238q) will cut rail & stile for cabinet doors in a classic round over design. Fully enclosed ball bearing guides allow for precise rail and stile cuts without the use of a fence. Two flute carbide cutters & 1/4" Shanks. Yonico rail and stile router bits produce impressive and perfect results with every cut yielding years of woodworking satisfaction.
8pfe
2025-08-28 13:00:14
I needed to make a replacement cabinet door with rails and stiles. Although this was my first attempt at doing this, I was amazed how well these router bits performed. I practiced with them on scrap pine wood to make sure I was doing it right then transitioned to oak and the door is beautiful.
Daniel Parent
2025-07-15 17:56:59
These bits are pretty decent for the price. I ran enough oak for around 20 doors. I made 2 passes per bit recommendation of 1/4" cuts. I found that they worked better with 13/16" wood for the round over portion. The rail bit tended to burn the wood and had a lot of wood blow out unless you backed it up with another piece of wood. The stile bit ran a lot smoother and worked better, obviously end grain cuts are a bit harder. They seem to be pretty decent quality for the price. My center panels were made of 1/4" oak veneer mdf. They fit fairly tight. I based my 4 star review mainly on price you can buy 3 sets of these for the price of some other brands.
CLINT S.
2025-04-28 18:42:15
I've been using them for a while with no issues.
StephenH
2025-04-15 18:20:22
These are somewhat tricky to set up and use. I had to settle for this profile as it was as close as I could get. The problem is in finding the right combination of router speed and material feed speed to be able to make accurate rail and stile cuts. I got these because they were 1/4" shank. After figuring out that I couldn't get a good cut with the older Craftsman router (the chuck would let the bit slip and the high speed introduced a significant vibration), I bought a Bosch router. It did a much better job. However, had I known what I do now, I would have looked for 1/2" shank bits as the Bosch router can use either and the 1/2" shank would probably be more stable.That being said, I am overall pleased with these bits. The cabinet door I made looks good and the bits held up well to this project. I may be making more doors in the future, which will give me the opportunity to further test their durability.
Jeff
2025-02-12 17:43:21
These worked great! I'm glad I bought them. Great price. I would recomend them to any carpenter or wood worker.
Chris
2025-02-06 13:36:34
Well first time using the bits and shaft is bent. The bit was out of balance and worked it’s way out of the collet. Good thing I had the guard down or it would have hit me in the head. A broken guard is better than stitches. Make sure to look at the shaft prior to using them.
Wayne
2025-01-19 16:27:28
I'm always a little concerned when something I buy is a great deal. This was my first time making cabinet doors and they turned out good (not great). I think the results were due to my inexperience, not the bits. I would recommend these to anyone. I'm looking forward to the next project, now that I've learned some of thing not to do.
Nosmo King
2025-01-18 10:31:11
Works well enough for the price. WARNING: keep bits as close as possible to the chuck mount. Not well balanced and will bend the 1/4" shaft readily. Joints will not be as tight as presented in product photo. Supplied shim washers help to get better joint results.
John Miller
2024-11-17 10:41:39
Worked as expected, well made
Recommended Products
$135.00
$ 65 .99 $65.99
$139.99
$ 60 .99 $60.99