Your cart is empty.
Your cart is empty.Juyancao Electric Linear Actuator Motor,12V High Load 22lb Linear Actuator 12mm/s Linear Actuator Stroke with Mounting Bracket
Norbertosantiago
2025-09-05 17:08:57
Work perfect for my Scag machine open and close the discharge
Clinton Chaffee
2025-08-24 18:56:05
Not much money and seems to function well so far
luis
2025-08-22 14:05:50
It work good for a few weeks only pushing less than 10 lbs with ocf wires and relays , actuator motor failed
Eric Perkins
2025-07-31 13:54:40
Used this to move a 3D printer away from the wall, on a sliding shelf. Down click on the latching momentary button moves it out where it stops and turns the printer on, when its done the up click on the button moves it back, switching it off and parking it out of the way. Works great and really adds a cool and wow factor to the shop. See if you get that anywhere for $25.
hope
2025-07-16 12:15:56
Power and speed are perfect for my application so far nothing in cons yet
Paybackone
2025-07-12 17:27:00
The media could not be loaded.
peregrine16
2025-07-11 15:57:08
Most actuators run at speeds that are much too slow for a chute deflector.This guy runs at 51mm/s - 2.00 inches/s. My John Deere has a deflector travel of 3 inches so if I use the original holes this actuator goes through its 3 3 inch stroke in 1.5 sec. This actuator has built in limit switches. In order to take advantage of them, all one needs to do is careful placement of the mounting points. In my case, in order to take advantage of the 4 inch stroke, I must point the upper mounting farther away from the hinge.Most people are not using these actuators at it's maximum. Locate the actuator where it will take the 4 inch stroke. A lot of folks out there should be placing the actuator closer to the hinge.A final note: So many people feel the need to leave the bolts on sides of the shute. Don't need them and they just create needles friction.
Norbertosantiago
2025-06-23 10:49:00
Work perfect for my Scag machine open and close the discharge
Clinton Chaffee
2025-05-29 17:17:22
Not much money and seems to function well so far
luis
2025-05-28 18:28:40
It work good for a few weeks only pushing less than 10 lbs with ocf wires and relays , actuator motor failed
Eric Perkins
2025-05-12 19:14:24
Used this to move a 3D printer away from the wall, on a sliding shelf. Down click on the latching momentary button moves it out where it stops and turns the printer on, when its done the up click on the button moves it back, switching it off and parking it out of the way. Works great and really adds a cool and wow factor to the shop. See if you get that anywhere for $25.
hope
2025-05-09 14:11:19
Power and speed are perfect for my application so far nothing in cons yet
Paybackone
2025-04-27 10:13:29
The media could not be loaded.
peregrine16
2025-02-15 16:38:32
Most actuators run at speeds that are much too slow for a chute deflector.This guy runs at 51mm/s - 2.00 inches/s. My John Deere has a deflector travel of 3 inches so if I use the original holes this actuator goes through its 3 3 inch stroke in 1.5 sec. This actuator has built in limit switches. In order to take advantage of them, all one needs to do is careful placement of the mounting points. In my case, in order to take advantage of the 4 inch stroke, I must point the upper mounting farther away from the hinge.Most people are not using these actuators at it's maximum. Locate the actuator where it will take the 4 inch stroke. A lot of folks out there should be placing the actuator closer to the hinge.A final note: So many people feel the need to leave the bolts on sides of the shute. Don't need them and they just create needles friction.
Recommended Products
