Your cart is empty.
Your cart is empty.Product Description
Biantie La 3-Pin 10mm LED Strip Connector
Featuring an innovative clamp-on design, these 3-pin connectors simply snap onto the copper pads of your LED strip to create a permanent joint. Slowly clamping down the connectors with a pair of pliers (not included) presses the contacts together, allowing power to flow freely through the connection. Once secured, the connectors cannot be detached.
10mm CCT Strip to Wire Connector
Installation Tips:
- Confirm proper polarity alignment
- Press connectors firmly until secured
- Maintain proper wire gauge specification
- Rated voltage: 0-36V
- Rated current: 5A
- Interface type: 3pin
- Strip width: 10mm
- Working environment temperature: -20~50℃
3-Pin 10mm COB CCT Strip Connector
What's Included:
- 5 Strip-to-Strip Connectors - For end-to-end jointing of 10mm COB LED strips. Simply snap strips into the connectors and clamp down with pliers (not included) to create a secure bond.
- 20 Strip-to-Wire Connectors (10 reverse compatible for wire-to-strip) - For connecting 10mm CCT COB LED strips to 22 AWG power wires or controllers.
- Connector Type: 3-Pin LED Strip Connector for 10mm COB CCT strips
- Compatible LED Strip Width: 10mm (Not compatible with 5mm, 8mm, or 12mm)
- Compatible Wire Gauge: 22AWG standard 3-conductor wire
- Connector Quantity: 25 solderless LED strip connectors (LED strip lights and wire not included)
How to use the 10mm 3-Pin connector
1. Insert Wire
Insert the 22AWG wire into the opposite port, just please align the positive and negative poles of the light strip
2. Insert LED Strip
Place one end of the 10mm LED strip into the connector strip port. Ensure the LED strip is 10mm wide with 3 solder pads.
3. Lock the Connection
Press down firmly on the clip to secure the connection. Use pliers for extra hold if necessary.
4. Installation complete
They cannot be reused. Make sure clip them right the first time.
Custom-length connections and jumpers
Strip to Strip Jumper
L Shaped Connection
Strip to Strip
Biantie La 3-Pin 10mm COB LED Strip Connector Kit
Featuring a range of 25 compact connectors to join strips end-to-end or attach to power supply and controllers, you can easily configure custom lighting for residential, retail or commercial spaces.
William Recher
2025-08-29 13:42:51
Great product
Jonathan
2025-08-05 13:43:01
These are absolutely hateful. The prongs bend very easily and when they do work, are impossible to remove without damaging the LED strip. Not happy.
sandra evans
2025-06-29 11:17:40
The pins that you clamp down bend VERY easily causing a failed connection. Then I had to use another. Very frustrating.
Bryan
2025-04-03 16:09:03
2 issuues with any of the COB connectors:#1 they're not reusable. Make sure you clip it on right the first time or you will be cutting your strip short and wasting a connector.#2-be careful when pushing the pins in as they easily bend. Once the pins bend the connector is rendered useless.
Daniel S Jameyson
2025-02-11 13:27:15
The contacts bend too easily, and when that happens, it damages what it's connected to. In this photo, one contact did pierce part of a COB strip, and it was impossible to remove without ripping that contact point.This was a nicely fitted 2m section, and the damage means hand soldering, or placing a new section of COB strip. Both are expensive wastes of time, and resources, which I will never recoup.I am discarding this, and not returning it, because the effort to return it is worth far less than my effort in mitigating the damage.
Daniel
2025-02-08 16:24:48
Its a great product if you know how to use it
praveen
2025-01-20 16:51:55
Poor design, wasted multiple connectors, not connecting the wire. Either Too small or mixing 1 wire to another wire. I cannot adjust after the click, have to cut the strip if it not works
Customer
2025-01-17 16:36:45
Using these with fcob cct from btx. Each one had a bad connection.
Jay
2024-12-27 14:14:54
They worked for I needed them for. All you need is scissors and pliers to cut and crimp your connectors. I wish you could buy the strip to strip connectors separately because I didn't need them.
Recommended Products