Your cart is empty.
Your cart is empty.Product Description
Product parameters:
Voltage: 6V~30V(support micro USB 5.0V)
Output Capacity: can control no more than DC 30V 5A AC or 220V 5A
Quiescent Current: 20mA
Operating Current: 50mA
Operating Temperature: -40℃~85℃
Timing Range: 0.1seconds to 999 minutes(continuously adjustable)
Trigger Signal Source: High voltage level trigger(3.0V~24V), signal ground and system ground are not connected to improve system anti-interference ability(or you can connect them).
Optocoupler Isolation: improve the anti-interference ability, after the parameter setting, it will memory forever . Warning: Relay contact is passive and electricity production; 1 channel has the control function on / off.
Operation Mode:
P1: After triggering signal, switch is connected for "OP" time, then disconnected; within the "OP" time:
P1.1: if trigger signal again, it is invalid.
P1.2: if trigger signal again, restart timing.
P1.3: if trigger signal again, switch is disconnected, stop timing.
P-2: After triggering signal, switch is disconnected for "CL" time, then switch is connected for "OP" time, and disconnect after timing.
P3.1: After triggering signal, switch is connected for "OP" time, then switch is disconnected for "CL" time, and enter loop. If trigger signal during loop, switch is disconnected and stop timing. The loop times (LOP) can be set.
Mark
2025-08-26 16:42:42
As title says. I’m using these to trigger my Halloween animatronics. Pretty easy to program and run off micro usb or dc power. I have my props set to run every 5 minutes broke up in intervals. Will always use these on props from now on. Great value for the money verse spending big money on a picoboo
layla jean arnold
2025-06-04 17:51:10
i made a controller for a pellet stove with them a pellet stove cycles several hundreds of times for the feeder auger and fan the fan relay would fail after about 6-8 weeks at 3 sec on and 2 sec off but no complaints here i did abuse lol adding an solid state auxiliary relay fixed the problem they are a great inexpensive way to experiment and build control devices
Jared wright
2025-05-02 18:58:15
These are extremely hard to figure out but you eventually get it. YouTube videos are your best friend
Jeff B.
2025-03-06 15:08:49
It's a little troublesome that they don't come with instructions but it's simple enough to figure out. My RV has lights that come on inside when the door is opened and go off when the door is closed. I wanted the lights to stay on for 60 seconds after the door is closed. That gives us plenty of time to turn on the lights in the coach we want on. Easy enough. This timer works and will do it. Only problem is just in the powered mode, not conducting any power through the relay, the back of the circuit board has a small spot that gets hot, and I do mean hot! It's hot enough that you will not leave your finger on it. I bought the 4 pack and tried two, they both get hot. I was going to mount this behind the panel the light switches are in but I'm no way going to have something that gets this hot just powered up. I could understand if the load was too high, but it gets hot with no load even wired to it. I'm afraid it may cause a fire. Just not good for me.
Branden Bayview
2025-01-08 16:50:19
Worked as described and seem quality. Good value as you get 4 of these. I used mine to constantly trigger a Halloween prop that had a 'trigger in' RCA plug. Worked like a charm, but had to watch a video on YouTube to know exactly how to wire it / program it. Instructions could be more robust
Wade
2025-01-04 16:11:32
I bought these to try and add to my Halloween props and after watching a few videos found these to be easy to setup. Glad I bought these.
John Stovall
2024-12-10 18:01:24
I bought these for Halloween props and it took some reading, fiddling, and finally finding a online video where someone actually showed how to program it. It makes sense once you know, but I wouldn't recommend for a beginner unless you like a bit of a challenge.
Recommended Products