Your cart is empty.
Your cart is empty.A510C Features: -Pro/Tran 2 series is UL listed to UL standard 1008 and is suitable for use in accordance with article 702 of the national electrical code ANSI/NFPA 70. -Made in the USA. Country of Manufacture: -United States. Product Type: -Transfer switch cover. Hardware Finish: -Painted steel cabinet. Finish: -Steel. Dimensions: Overall Height - Top to Bottom: -11.25". Overall Width - Side to Side: -11.75". Overall Depth - Front to Back: -4.5". Overall Product Weight: -19 lbs.
Robert P.
2025-08-24 13:51:47
The generator is solid and started up right away. I like the fact the remote was already paired and charged. Assembly was easy and the price was great for the value. Came with the oil to add to the crankcase. The controls are easy to access and use. Plenty of receptacles and optins. Overall, I am pleased so far with the product
rb32
2025-08-20 10:55:55
This was easy to install and works great! I had to install it on the opposite side of the electrical panel than where I wanted because the loom of wires had to enter the box on that side. I had to cut drywall as there was no way to fish that large wire and finish the connectors. It looks great and works great. It is easy to use. A great product.
Customer
2025-08-15 13:12:52
For my install I needed just a little more flex conduit than was supplied with the unit, so I got a little longer and got it in 1" flex so it made it so much easier to push the bundle of wires thru the flex. Install was easy and only had to pig tail a couple a wires to reach the brakers. Check into the abbreviated codes for the different transfer switches so you order the right one you need.
curlgary
2025-08-08 11:36:32
I installed flush mount recessed into sheet rock wall using trim kit, as photo shows:https://www.amazon.com/dp/B00REJVYYG?psc=1&ref=ppx_yo2ov_dt_b_product_detailsVery well built and well laid out to install yourself. Cables all labelled to match throw switches. Get a good layout of your house breakers before you begin, so you know which ones to run through the transfer switch. I removed the jumper for positions C&D and only used A&B for 220V. That left me 6 15 amp and 2 20 amp for other circuits. Will run everything I need plus bottom floor air and heat. Good videos on YouTube to install the Reliance Pro/Tran. Reliance Contral Products customer support is fantastic and quick. Had some questions, contacted them by email, and had answers the same day. Guenther handled my emails and was great to deal with. This is a super product, very well laid out, and very well made. Cable tails are plenty long to reach anywhere in the breaker box. I had to cut length off all of mine. Give this one a look if looking for a transfer switch. Mine will work from an outside portable generator. I ran 6-3 w/grd from the transfer switch to an outside wall plu,g to plug the generator in. Got great plug from Amazon also. It is also a Reliance Control Product:https://www.amazon.com/dp/B004HSO1JW?psc=1&ref=ppx_yo2ov_dt_b_product_detailsAs you can see from photo I fixed a label under each transfer switch poooooosition showing the breaker number it was feeding. The only suggestion I would have to improve the box install is the have terminals to attach to for incoming wire from the gerator instead of have to splice with connectors, but was not a big issue.
Al G
2025-07-21 14:18:06
This is a great tool for people who want to have a fairly easy way to tie solar into a main breaker box. The box itself is robust and well made. All the connections on mine were nice and solid. The wires are well labeled and plenty long (at least for me). Mounting is also very simple whether surface or inset.I did hire an electrician to work with me on the install because I wanted to make sure things were well installed and organized in my very old main breaker box. We ran from my inverters (2 inverters for split phase 220) to the bypass box and then bypassed my heat pump water heater, the dryer (useful as a dump load) and some 110 critical loads.Now if I want to go on battery (solar), I just flip the bypass switch or switches to GEN. If my batteries get low and need to give the system a break, I can flip back to line power. It’s very convenient. The 50 amp capability means if I get larger inverters, I’m good. I ran beefy wire from the inverter junction box over to the bypass box. All I’d have to do is swap inverters and do some easy wiring and I’m golden.I’m very happy.
J Gardiner
2025-07-19 14:06:30
Switch arrived quickly,packaging was good,installation was a snap. Zero issues other than it did not come with wire nuts. But that's not a big deal,very solid product. Install took about 2 hours,mostly because I had to mount my inlet to brick that was a pain to drill though.pulling wire and hooking it up simple and clean.
David B.
2025-05-26 11:39:43
I added a second solar system to my off grid home….I use this now to share the demands between the 2 systems. Been using it for a few months. No issues. Everything you need all in the box. I would buy again.
Ashley J.
2025-05-02 13:02:07
This made installing the transfer switch much easier.It’s a US made switch so I can rest assured it is safe to operate. The instructions are basic but they have a series of YouTube videos to install it.You will need a male adapter plug and I highly recommend getting the flush mount kit seen in the images.If you’re concerned about the #10 gauge wire inside, don’t be. It’s in a UL listed box and completely able to support a 50 amp circuit.
Alex Lazebnik
2025-04-02 18:03:49
Reccomended
Client d'
2025-02-17 16:30:18
facile à installer avec guide sur youtube
Recommended Products
$332.38
$ 99 .00 $99.00
$416.48
$ 99 .00 $99.00