Your cart is empty.
Your cart is empty.Product Description
DAWASAPAT Projector Mount 3-In-1 Universal Projector Wall Mount Bracket
This multi-functional projector mount is suitable for any installation. Made from solid steel for durability with minimal vibration compared to aluminum models and is suitable for ceilings and walls. Find the best projection angle with pitch, roll, height adjustment (from the ceiling), and extension from the wall. The quick-release connector allows the projector to be installed quickly and released for maintenance without re-alignment.
Adjustable & Sturdy connection
You can use this extension pole depends on your need. If you want to slip your power cable and HDMI cords through the arm, recombine the parts to have your 2-piece extension bar.
Angle adjustable
Great hardwares
Through this whole part, keep in mind which way the projector will point. Identify the mounting bolt holes on your projector. If only has 3, just only use 3 of the parts.
Will this projector mount fitting for me? Please check the following detail:
- Our universal extending ceiling projector mount fits the majority of projectors on the market. Check the mounting holes on the top of your projector and measure the distance between each hole. Your projector mounting hole must be between 8.85" -12.44”.
- Please check the wood studs on your ceiling. This mount can also be used on concrete and brick ceiling. NOTE: does NOT support vaulted ceiling and drywall.
- Please check the weight of your projector, the projector weight should be less than 40 lbs.
- Notice!!!
- The projector mount must be installed on a level ceiling or wall but not an arched one. If it is not installed correctly, it may fall and cause property damage or personal injury.
- This product contains small accessories. If accidentally swallowed, there is a danger of suffocation. Please keep these accessories away from children.
3-In-1 retractable projector mount, including Flush Ceiling Installation,Telescoping Arm Ceiling Installation,Wall Installation.
- PLEASE don't get overwhelmed by the number of parts. Pack list: Mounting Plate /Extension Arm /Bracket /Pan & Tilt Swivel/Expansion boltsx4 /M5x11 bolts/M4x4 bolts/M3x4 bolts/Small Platex2/Washerx4
- Except for the excluded accessories, please prepare the necessary tools, such as pliers, screwdriver, or drill, by yourself for a smooth installation.
- Detail Installation Guide:
- Step 1: Use the mounting plate with the expansion bolts to mark a position you want to install the projector.
- Step 2: Use the M5 screws to screw the mounting plate with the extension arm. The extension arm is stretchable, you can adjust it to a proper length by losing the screw on it.
- Step 3: Insert the Pan & tilt the swivel into the bracket and fixed them with M5 screws, tighten all the screws with your screwdriver.
- Step 4: Use the M5 screws to connect the extension arm with the bracket, align the holes, fix them with the M5 screws, and then tighten them with your screwdriver.
- Step 5: Connect the finished bracket with the projector. Needs to use M4 screws(Some projector fits the M3 screws) and the screw washer. The Bracket is expendable and stretchable, align the holes on the long plates with the mounting holes on the projector top to check if they fit each other. If the bracket doesn't fit the holes, you can use the 2 small plates to do the trick. (Lose the nuts on the long plates and took them out, use the M4 screw to fix the small plate according to the holes on the projector. Insert the small plate into the bracket, and screw the nuts a little bit). Adjust the angle of the bracket as needed, then insert another two screws into the projector. Tighten all the screws with your screwdriver, and then tighten the nuts.
- PS: Before fix the projector on the ceiling or wall, please take it with the mount to the ceiling or the wall, then power on the projector to check the best projection position. After selecting your ideal position, mark the holes with a pencil, then drill four holes in the ceiling or the wall based on the marks, and fix the projector with the expansion bolts.
- Finally, fix the mounting plate with the expansion bolts.
Palak
2025-09-01 09:12:10
The media could not be loaded.
Gigger’s
2025-08-23 12:12:33
This mount will work on the ceiling or from the wall plenty of adjustment and looks good
Robert Klaproth
2025-06-07 13:02:27
We got a Fangor projector here on Amazon (which is great BTW!), but the projector only has one hole in the middle to mount it, not the four screw holes as pictured on this mount. So, we were able to screw one of the brackets that came with this mount into the middle of the projector and then went to Home Depot and got a few rubber washers to help stabilize the projector and it works great. The directions leave a lot to be desired but all in all, the mount is sturdy, and it's white so it blends in with the ceiling on our outdoor patio. I'm hoping the paint holds up over time for outdoor use, I'll update my review if it does end up rusting.
GC
2025-05-25 12:46:24
My projector is not that old and it was very hard to make it work. I needed to invent different hardware. It only comes with cement anchors not drywall or ceiling. Luckily, my husband is very handy and made it work.
K
2025-03-09 18:18:48
I'll start by saying that the installation was pretty easy, and the mount seems like it'll work pretty well. With that being said, it's not perfect. And required some minor modifications and installation adjustmentsThe biggest issue I found is that it definitely doesn't have the advertised 360* swivel action. In reality, there's basically no swivel if installed as outlined in the instructions. Fortunately, the solution is pretty simple. Just remove one of the two bolts that comes installed in Pan & Tilt component that attaches to the mounting plate (see picture). It'll still be plenty strong with only one bolt installed, and will then allow you to easily swivel/rotate the projector from side to side. A nice bonus is that it frees up an additional M5 bolt (which will come in handy later).Another minor issue I found was that the included hardware to mount the bracket to your projector was insufficient. They specifically include m3 and m4 bolts for mounting the bracket. But many projectors use an M5 thread pattern. Fortunately, there were a couple extra M5 bolts. And by choosing to install only one M5 bolt in the pitch holes (also pictured). And by removing the above mentioned M5 bolt to allow for swiveling the projector. There were just enough M5 bolts left for the bracket to projector mount.Other than that, everything went together pretty easily. My projector's footprint is a little smaller. So I had to swap in the two included Small Plates into the bracket. I also didn't use the included expansion bolts (anchors), as I was able to secure the mounting plate directly to a solid wood surface. However, to do this the holes in the mounting plate weren't ideal. So I drilled a couple new ones on each side. In doing so, the metal seemed pretty soft. But should still be good enough for this application.Overall, it's a pretty good value. And may work just fine for folks without any modification or installation adjustments. Once installed, it's fairly sturdy, even though the metal seems to be a little soft.Giving it 3 stars because if installed as instructed, the advertised 360* degree swivel functionality is non-existent. And while this was an easy fix, the claim of 360* swiveling was not at all accurate.
Aries
2025-02-20 12:24:27
I eliminated the TV in the living room put this up with my projector and now I watch TV on a wall is a very good purchase if anybody is interested in purchasing this I recommend it it was very easy to put up in the value for the money was good the design worked and it does adjust works well
Samantha W
2025-01-11 11:28:26
Like others have stated the instructions are completely unhelpful. The installation process is unnecessarily complicated and comes with many confusing and unneeded things. It also doesn’t come with any way to just mount it with the middle screw mount that most projectors have for a standard mounting. Many screws that are supposed to fit just simply don't and thats after reading the instructions numerous times to verify they're the correct ones. I chose this one because it was white and wouldn't stand out in my living room but now I'm regretting that decision after trying and failing to install this mount for the last 40 minutes as a moderately handy person.
B. gladden
2024-11-23 14:57:31
We didn't need the extension but I wanted the universal because we may install elsewhere later. It came with some serious concrete anchors but nothing for drywall. Definitely dry fit everything because there's a lot of transferring and we almost installed several things backward (we were drinking though so it may be us). We really like that the assembly on the projector hooks on to hold the projector so you can then play with the gimble adjustments.
Recommended Products
$67.79
$ 27 .99 $27.99