Your cart is empty.
Your cart is empty.Bits are designed with a 1/4" Cutting edge for dado clean-out. Also used in hardwood and flooring medallions, #45489-S, diameter (D): 1/2, cutting Height (B): 1/8, shank (D): 1/4, overall length (L): 1-3/4, replacement collar: 47724, replacement bearing: 47701, flutes: 2, 45489-S carbide Tipped dado clean out 1/2 dia x 1/8 x 1/4 inch Shank with upper Bb
Gary Williams
2025-09-05 12:37:28
Amana routing bits are some of the best bits in the world. They are sharp, tough and will out cut and outlast almost any other brand period. My only complaint is that they are so damnxx expensive!!
Gordon L. Malboeuf, Jr.
2025-09-01 16:23:21
This tool is awesome. I could not have been successful without it. First, I roughed out the pockets to full depth in multiple passes with a .125 carbide upcut bit using an inlay kit guide without the bushing. Then I switched to this bit and completed the pockets in two passes (depth). Super sharp bit easily cut this end grain cutting board like butter. Highly recommend if you looking for precise controlled cutting for intricate designs. I also used the flush trim bit to create the inlay pieces on my router table. The results are stunning.
Chuck9
2025-08-27 12:36:18
This is a fantastic router bit when used properly. It seems fairly fragile so I'd never try to cut more than a few mm of depth at a time or cut too quickly with it. But taking shallow cuts and working slowly up to the pattern, I'm able to make recesses for illuminated guitar truss rod covers. It cuts so cleanly and thoroughly that it left a shiny surface on the wood I used it with. Had no problem cutting through maple, mahogany and cherry.
KSCat68
2025-08-21 09:10:18
Bought this for a dado jig that I made and it has worked fine. No issues with the bit and look forward to using it for quite some time.
Joe Swaika
2025-08-09 15:51:37
Bought it for closet door pulls and worked great for the price
TimBob
2025-08-01 16:54:05
Love it.
corey
2025-07-27 14:12:48
I usually use Whiteside bits but this popped up when I was going to order so I thought I’d give it a try. It’s always whiteside and amana that are recommended for good quality bits and I just started with whiteside and have never had a reason to not use them and regret not using them for this but. The very first time I used it the collar came loose and the bearings slid up allowing the bit to dig into the material and ruin the project. I will just stick to whiteside after this. Definitely would not recommend! Ridiculous!!
Joseph Gersky Jr
2025-07-15 14:55:57
Item arrived as advertised,Thank you.Regards,J.G
Prinz Midas
2025-07-04 12:57:56
Also ich weiß nicht ob ich Ausschuss bekam, aber dieser Fräser hat keine 5cm gefräst, dann waren die kompletten Schneiden abgebrochen. Eine hab ich noch gefunden. Die andere... zum Glück hab ich sie nicht abbekommen. 3mm in der Zustellung bricht der einfach ab... Schrott!
oryan
2025-06-20 15:11:11
I got this bit to lower the neck pocket of a guitar body. This has a proper stopper for the bearing as opposed to the one stewmac sells which only has a plastic tube.Smooth bearings and a very sharp bit.
Customer
2025-03-11 14:39:10
I first and tried the Yonico drill bit. It was very rough and of inferior quality. The Amana was much smoother and did a perfect job. After the Yonico I won't buy Chinese made tools.
PHANTOM
2025-01-17 15:47:12
De acuerdo a la descripción. Muy buena calidad, funcionales y duraderas.
Recommended Products
$95.10
$ 42 .99 $42.99
$82.31
$ 35 .99 $35.99
$25.95
$ 11 .99 $11.99