Shopping Cart

Your cart is empty.

Your cart is empty.

ASHATA 2 Way 2 Unit Hi-Fi Sound Filter Audio Module Board, Speaker Frequency Dividers Crossover Filters, 150W, 4-8, 3200Hz, 2 Channels, Part Number: ASHATA3ryebni80q

4.9 (7) Write Review
Free shipping on orders over $29.99

$16.07

$ 7 .99 $7.99

In Stock

About this item

  • 【Professional Frequency Divider】 This is a professional frequency divider which is widely installed in the speaker. Plays an important role in the segmentation of the overall frequency . In order to separate the mixed audio into treble and bass, these were sent to the corresponding loudspeaker unit for treble and bass during playback, which resulted in an improvement in the sound quality.
  • 【 HIFI Sound Quality】Make the treble clear and increase the of the bass, freely enjoy clear and music.
  • 【Treble and Bass Dual Frequency Dividing】Widely use in treble and bass speakers, car full frequency speakers, or use treble/ bass alone.
  • 【High Quality and Super Durability】Wire wound ceramic resistor and high-quality metal film capacitors, ensure its large load power, long-term durability, never burnout.Circuit board design with cutouts and lines, for welding, very suitable for DIY.
  • 【Professional After-sale Service】100% new product guaranteed. We provide quality assurance, if you have any questions, please feel to us, we will do our best to solve the problem for you and provide you with a satisfactory answer. (Returns are supported).


Product Description

Frequency Divider

Description:

This is a professional frequency divider, which is widely installed in the speaker. Playing an important role of the total frequency signal segmentation. Treble and bass dual frequency support, helps to transmit the treble signal to the tweeter unit, and divide the bass signal into subwoofer unit. High quality and free welding.

Frequency Divider
Frequency Divider
Frequency Divider

Specifications: Type: 2 Way, 2 Unit (Woofer and Tweeter)

Frequency Crossover: 3200Hz

Power: 150W Max.

Resistance: 4 - 8Ω

Welding:

- T for tweeter

- W for woofer

- IN for amplifier

Size: Approx. 70 x 57 x 26mm / 2.8 x 2.2 x 1.0in

Package Weight: 236g

Package Includes:


Matthew Robert Mattingly
2025-08-10 18:55:59
These bad boys took a 4 hour beating and made it through 4 punk/ trash metal bands at around 500 watts rms 1500 peak per channel. Used them in a quick diy line array cabinet with 4 8in drivers on the lows and 2 compression drivers on the high side. So yes the lows were wired at 8ohms and the highs at 4ohm and it worked and sounded fine. Recommend.
Tony
2025-06-28 18:41:38
It doesn't have connections for input and for the drivers. I will try and figure something out.
Raymond Joestgen
2025-05-23 18:02:01
The media could not be loaded.
Jason
2025-05-09 18:19:24
Soldered the crossover on a centre channel that the existing crossover was defective on. Fixed no problems.
Tammy Lynn Pahl
2025-04-04 09:02:17
I purchased these for some cheaper car speakers because there was no filter for the woofer and only a small capacitor for the tweeter. I believe these help the speakers produce a more accurate and natural sound. Most actively driven speakers or top-of-the-line speakers have 12 dB/octave crossovers, so these are an excellent buy for 30 bucks.
james e.
2025-02-15 12:03:51
They were easy to install but wish the holes where the wire goes through to solder would accept a little heavier gauge but not really complaining, as advertised, good seller!
Jose Rivero
2024-12-31 18:03:55
Home made speakers.