Your cart is empty.
Your cart is empty.Product Description
BESTTEN Motion Sensor Switch
BESTTEN motion sensor switch is designed to detect motion from a heat-emitting source (such as a person entering a room) within its field-of-view and automatically turns the lights ON. The lights will remain ON until no motion is detected and the scheduled time-delay has expired.
- Advanced passive infrared (PIR) technology
- Occupancy (OCC)/Vacancy (VCC) mode
- Works with 300W LED, 800W incandescent/fluorescent
- Adjustable light level/Adjustable sensor sensitivity/Time delay control
Operation Instructions:
OCC Mode: Auto ON, Auto OFF
VAC Mode: Manual ON, Auto OFF
TIME：
You can adjust the time delay to turn the light off at preset intervals of 15 seconds (Test), 1 minute, 5 minutes, 15 minutes, 30 minutes of inactivity.
SENSOR:
Adjust the sensitivity setting to desired detection range. Turning the setting counter clockwise will decrease sensitivity while turning it clockwise will increase it.
LIGHT:
Light setting is used to adjust the detected ambient light level. The switch will turn on when the light falls below the set ambient light level. If ambient light level is desired, please turn the adjustment knob counter clockwise, and push the button to make sure the sensor start to work. If the ambient light sensor is not needed, please set it to the maximum setting (Position 5). This will allow the sensor to turn on and off regardless of ambient light conditions.
Wire Guide:
Before purchase, please confirm that there is a Neutral Wire available in the wall box you intend to install this switch. It can be identified by 2 or more white wires connected together in the wall box without being connected to a standard switch.
HOT: Identify the Hot Wire in the wall box which has power from the breaker pannel. This is usually a black wire. Connect it to the black wire on this switch.
LOAD: This is usually the other black wire which delivers power to the light and does not have power. Connect it to the red load wire on this switch.
Neutral: Connect the white wire on this switch to the existing Neutral wire.
Ground: Connect the green wire on this switch to the existing Green or bare copper wire in the wall box.
loribeans
2025-08-28 12:05:06
We purchased an older home and my husband replaced all of the outlets and switch panels with these, and others from the same brand. What would have cost a small fortune if purchased from local home improvement stores was very affordable using these and just as good quality. Don’t hesitate!
vilasith
2025-08-26 12:40:05
Good product
Deanzae
2025-08-17 11:10:15
Confirm if your replacing an existing switch if the circuit has a neutral
The Blissett's
2025-07-31 11:50:45
These motion-sensing lights have a mind of their own. Sometimes they work, sometimes they don’t; kind of like that friend who’s always “on the way†but never shows up. When they do decide to function, they’re decent, but not reliable enough to trust when you actually need light.Also, the cover plate is smaller than a standard one, which means you get a lovely peek at whatever horror was lurking behind your old switch. If you’re into unpredictable lighting and exposed drywall, this is for you. One star for effort, but honestly, it’s a stretch.
Keith Parker
2025-07-28 17:43:15
Easy install
AR
2025-07-11 11:45:41
I installed the motion sensor in multiple locations.It works when you want it to detect but also works even when there is no movement. I was able to isolate issue with one switch that I installed in closet. Whenever the Hvac starts, the clothes might move that is triggering the light even when the sensitivity is turned low.But still havent found the cause for other locations as I am pretty sure there is no movement in that room. So I am guessing I drew short string for a faulty switch.
R_c_E
2025-06-22 14:01:50
Purchased these for our newly renovated building because all the lighting is 277VAC. Replaced the switches we needed and everything was great.....for a week. Then they slowly started dying, one by one. Any switch in a high traffic area of the building that keeps getting switched died the fastest. There is a reason for the price tag, trust me. I opened one up and you can see the "quality" of the components. Spend more money on a Leviton at HomeD and save yourself the headache of dealing with Chinese tech support at 1am in the morning. Lesson learned!
Naturals
2025-05-27 12:17:29
These did not work on my switches that had a ground, my lights were dim.I was able to use two sensors out of the whole box, you need at least 4 connection wires for this to work
Phyo T.
2025-05-24 14:46:07
The media could not be loaded.
Rajinder Singh.
2025-05-01 12:21:45
Saves energy and money.
polilo
2025-04-30 18:33:13
Three out of the five motion sensor switches are defective. We’ve tried playing around with the settings hoping for a miracle to make it work but it’s hopeless. We wish we can return them now it’s already past our eligible return date.
Client d'
2025-03-15 14:05:02
aucune
Customer
2025-02-11 18:26:30
Got the 5 pack, tried two and neither worked. Didn't bother wasting more time then I already did, returned them. Gave two stars because they look nice, and the instructions were very clear. It's too bad the quality just isn't there.
Recommended Products
$35.97
$ 16 .99 $16.99
$24.99
$ 12 .99 $12.99