Your cart is empty.
Your cart is empty.Product Description
Who we are and What we do ?
BLCH was a manufacturer , that produce and sale pneumatic components over 20 years. We offer more than 10,000 models of pneumatic products and provide automation solutions to customers worldwide.
detail of air filter
Preparation
1. Before installation, please clean up the dirty inside the connecting pipes and joints , and avoid to carry into the air system.
2.Please make sure the Max working pressure 10bar(145PSi) can meet your needs.
Double filtration
High precision pressure gauge, Clear calibration to reading easily
Dial Reading
Install the gauge on the body tightly
Check that if the pointer rotated smoothly
installation:
bracket and screws
Raymond Wakat
2025-08-30 16:40:01
The regulator on my compressor was leaking. After replacing with this my compressor is back in operation.
Barkfire
2025-08-26 15:54:43
I was surprised with the quality of this product for the price I paid. I am very satisfied and would recommend this to anyone that needs a nice air regulator.
R. C. Smith
2025-07-27 13:21:58
Works well as a wall mounted in line application. Too large to be mounted on the tool. Good quality construction, and easy to use. Good value for the price.
KcKerry
2025-06-03 12:51:21
Took a second to figure out the knob control but anyway works great on my double tank compressor.
jeff
2025-05-20 16:01:43
Good product!
Howard D. Gassett
2025-04-21 16:32:34
I ordered the first one and it leaked around the adjuster knob. Amazon REPLACED IT BUT THE SECOND ONE LEAKED IN THE SAME SPOT!!! I would not recommend this item.
mungo544
2025-04-11 13:06:20
Appears to be very high quality, however because of the size of the blue knob I couldn't spin the valve on my compressor without taking the valve apart. If you need to do this here are instructions: 1) Unlock the blue knob by lifting gently until you hear a click. Turn blue knob counter clockwise until it stops 2) Remove four philips head screws. 3) carefully lift top half off the valve. There will be a spring, a brass shaft and a rubber diaphram inside. Remove all parts and note how they go together.4) There is an arrow on the bottom of the valve indicating flow direcrion. Attach a bare nipple on that side and and then a quick connect on the other side. You only need to use 4 or so turns on the nipples using teflon tape. 5) thread the assembly onto the compressor, carefull not to over tighten until the gauge hole is facing you (there are gauge holes on both sides of the housing depending if you want the knob facing up or down. A bung is supplied to plug the hole you don't use for the gauge. 6) install the gauge. Don't over tighten. 7) reassemble the valve, tightening screws in a criss cross pattern.
bullit-hed james
2025-03-11 15:43:00
It is easy to use and works as it should. I use this with the latching air stems air trucks. To do air pressure on semis and trailers. Took five minutes of holding an air truck on each tire And has made it into I spend 45 seconds. Putting all 4 locking air chucks onto the tires. And walk away for 5 to ten minutes. Don't have to worry about the tires blowing up
Customer
2025-02-28 14:21:02
The regulator is excellent. The diagram (pictures) showing the input and output ports is wrong. The ports are actually opposite to the picture. Look for the tiny embossed arrow next to the input port (hard to see).
Customer
2025-01-20 18:26:02
Bought this to replace the regulator on an air compressor. Had to buy a longer connecting nipple in order for the regulator to clear the tank on installation, but other than that, the new regulator worked great.
Customer
2025-01-12 17:31:17
travail tres bien
Gilles Boivin
2025-01-11 20:48:01
La piece est de bonne qualité.Par contre elle n'est pas désigné pour mon compresseur.
Recommended Products