Your cart is empty.
Your cart is empty.Camco’s 2000W/120V Screw-In, High Watt Density Water Heater Element can be used in most replacement situations of the same wattage and voltage. High watt density (HWD) elements are the most common and the same type of element provided with most water heaters. This element features a 1-11 ½-inch NPSM steel bushing with copper sheath. Includes a gasket. Minimum tank diameter is 9-inches. It is compatible with most models of American, AO Smith, Bradford White, Craftmaster (prior to 1991), GE, GS Wood (certain models), Kenmore, Lochinvar, Maytag, Mor-Flo, Reliance, Rheem, Richmond, Rudd, Sears, State, Whirlpool, and all water heaters manufactured after 1994. Never exceed the nameplate rating on the water heater. UL listed for US and Canada. Includes a 5-year limited warranty.
austenut
2025-09-04 12:03:23
Our small water heater is not too common and this fits and works perfectly. No trouble at all installing it.
Customer
2025-08-21 10:45:29
Direct replacement, easy install and works great.
Mark
2025-07-11 13:27:23
Water heater, good quality and reasonably priced
Thomas Hanley
2025-06-11 09:26:07
ahhh hot showers again
Shelly J.
2025-05-05 10:12:34
My dad needed this, we looked several places in town and could not find it or have it ordered. A clerk looked it up on Amazon and was kind enough to show us. It was a perfect fit.
C Chocholek
2025-05-01 16:07:20
I'm using this on a home brew system to heat a 7 gallon HLT to 180 degrees. Works just fine on a standard 120 Volt 20 amp outlet. Water temperature started at 60 degrees and took an hour and a half to accomplish. During my timed test I did not have a lid on the HLT. Therefore, if the lid was in place, I would imaging the time would be cut by at least 15 minutes.Installing this on a stainless steel kettle is simple. You will need a 1 1/4" hole saw that is designed to be used on stainless. I purchased mine at Menards for $8.99 and a pilot bit for $3.97. Just read the carton to insure it can handle stainless. You will also need a round file to de-burr the opening.Purchase the silicone 211 O-ring, and stainless nut that everybody else recommends in their reviews. Tighten up the nut and wire it in. Make sure you use a cord rated for the wattage that is grounded. It is very important to use a ground on any metal container. If you don't ground the kettle you WILL be electrocuted if you touch the kettle while the element is plugged into an outlet.No I didn't use any controller. I just plugged it into an outlet.
celt67
2025-04-20 19:05:58
Put this in my new still and it worked flawlessly. Got 10 gallons boiling in the middle of winter in an hour and a half.
Roger W Stone
2025-04-14 19:06:19
As described, shipped fast, liked price. SuggestPutting antifreeze on threads to make removal easy.
Good
2025-03-28 17:27:36
It worked
Rafael Cruz
2025-03-03 16:57:40
El primer producto llegó con una falla, pero inmediatamente lo sustituyeron por uno en excelentes condiciones, que hasta la fecha no a fallado, quizá la primera sufrió un golpe o un mal manejo y se dañó por qué es una resistencia eléctrica muy frágil, debieron tratar con cuidado el paquete, sin embargo la atención y la calidad del producto es genial y funciona de maravilla mejor que la que tenia antes!!
Larry Paulson
2025-01-24 12:17:25
seems to work great. time will tell....
MarÃa de Jesús González Basilio
2024-12-14 18:30:05
Super precio, es lo que buscaba
Customer
2024-12-07 18:12:05
It works
Recommended Products
$15.88
$ 6 .99 $6.99