Your cart is empty.
Your cart is empty.Product Description
Lifted
2025-09-02 13:59:29
Drill and tap worked fantastic arrived on time quality Material
SteveTX
2025-08-30 16:12:00
I thought I needed the bit that was the proper size for the 1/8" npt tap so I order this matched set. I was needing the tap to install my over flow fitting on my TH400 transmission. Well turned out after removing the factory metal drain that the hole left in the case was bigger than the drill bit. Somehow the tap was still a perfect fit in the hole that was there. So I just used the tap and gently tapped my case for the fitting.The tap was very sharp and although it was only aluminum it still did a excellent job.Not sure why the drill bit was so much smaller than the hole that the tap fit perfectly. I feel like that drill bit would have been too small for this tap but I didn't get to use it so I cannot say for sure.
Mike Della Penna
2025-08-08 15:36:12
Very good combo . Met my needs
The traveling mechanic.
2025-08-06 12:21:34
Great to have the drill bit & tap together. I have learned over the years it just works better to order the kit & put it in a storage case with others I have bought the same way. Saves a lot of time looking for both.
The Walrus
2025-08-05 10:39:17
I got this for the tap; drill bit is a bonus.However, it bothers me that the product was packaged with the tap and the drill bit able to knock together in the packaging. Maybe an issue, maybe not. Someone smarter than me would have to weigh in.The tap worked fine. I appreciate that it has a standard square drive and works with the tools I already have.I was cleaning out an existing hole with damaged threads. The result is looser than I would prefer, but that may not be the fault of the tap.The drill bit is stamped "HSS". The tap is not.The packaging says made in Japan, India, or China (but is specific to 10/32). The tap is stamped "INDIA".
Thomas H. Best
2025-08-02 10:48:20
It worked for.me.
RJH
2025-07-23 17:34:01
Good quality, sturdy and long lasting.
Hinds90
2025-07-21 10:45:57
Worked great
Andrew Dumont
2025-07-13 13:42:01
Worked great for what I needed it for. I installed an egt sensor in my exhaust manifold on a Cummins 5.9
Alicia Harrison
2025-07-12 12:20:35
Item as described, cut great.For anyone doing the budget RSV4/Tuono block off plate hack, this tap is the right size.
Peter Ratcliffe
2025-07-06 15:00:27
Works well
Ronald Tremblay
2025-07-01 18:57:18
Quality precision tools +
Lifted
2025-05-29 12:20:34
Drill and tap worked fantastic arrived on time quality Material
SteveTX
2025-05-19 21:04:13
I thought I needed the bit that was the proper size for the 1/8" npt tap so I order this matched set. I was needing the tap to install my over flow fitting on my TH400 transmission. Well turned out after removing the factory metal drain that the hole left in the case was bigger than the drill bit. Somehow the tap was still a perfect fit in the hole that was there. So I just used the tap and gently tapped my case for the fitting.The tap was very sharp and although it was only aluminum it still did a excellent job.Not sure why the drill bit was so much smaller than the hole that the tap fit perfectly. I feel like that drill bit would have been too small for this tap but I didn't get to use it so I cannot say for sure.
Mike Della Penna
2025-05-07 14:33:32
Very good combo . Met my needs
The traveling mechanic.
2025-04-25 10:17:14
Great to have the drill bit & tap together. I have learned over the years it just works better to order the kit & put it in a storage case with others I have bought the same way. Saves a lot of time looking for both.
The Walrus
2025-03-16 10:09:06
I got this for the tap; drill bit is a bonus.However, it bothers me that the product was packaged with the tap and the drill bit able to knock together in the packaging. Maybe an issue, maybe not. Someone smarter than me would have to weigh in.The tap worked fine. I appreciate that it has a standard square drive and works with the tools I already have.I was cleaning out an existing hole with damaged threads. The result is looser than I would prefer, but that may not be the fault of the tap.The drill bit is stamped "HSS". The tap is not.The packaging says made in Japan, India, or China (but is specific to 10/32). The tap is stamped "INDIA".
Thomas H. Best
2025-02-24 11:33:20
It worked for.me.
RJH
2025-02-23 15:53:32
Good quality, sturdy and long lasting.
Hinds90
2025-01-12 11:00:30
Worked great
Andrew Dumont
2025-01-11 17:14:24
Worked great for what I needed it for. I installed an egt sensor in my exhaust manifold on a Cummins 5.9
Alicia Harrison
2025-01-05 14:23:11
Item as described, cut great.For anyone doing the budget RSV4/Tuono block off plate hack, this tap is the right size.
Peter Ratcliffe
2024-12-26 15:13:27
Works well
Ronald Tremblay
2024-12-25 14:32:45
Quality precision tools +
errol cooper
2024-12-07 15:54:31
Just what I needed
errol cooper
2024-11-17 10:34:44
Just what I needed
Recommended Products