Your cart is empty.
Your cart is empty.Product Description
The screen is not included!
JM
2025-08-28 10:57:44
This cooler does a great job keeping my Raspberry Pi 5 temps in check, even when overclocking. The fan is efficient, and the aluminum heatsink helps dissipate heat really well. Installation was simple, and the build quality feels solid. If you're pushing your Pi to its limits, this is definitely worth it to keep things running cool and stable.
Cadstar
2025-08-03 15:51:32
Love this cooler, it's my go-to solution for Pi5. Looks better than the Pi Foundation's version and has a quieter fan design. Fits nice and snugly to the PCB so the Pi still fits most cases and uses scenarios. I use a Geekworm X1001 NvME board atop this cooler - gave it a touch more room with some additional spacers to prevent blocking the fan intake. This setup works great and even under Stressberry 15min load my temps never go over about 67F
Jeff B.
2025-07-31 10:31:03
This cooler works well. It came with more than enough thermal pads. It attaches with nylon screws (Probably keeping you from over-tightening). Plugs into RP4 fan header. I have zero issues and my Pi no longer thermal throttles. I also like the fact it's pretty low profile and doesn't stick out past the usb housing
Polar Bear
2025-07-20 13:16:27
I had passive heat sink, however they just didn't cut it for a demanding application (video + AI)I was reluctant to get a fan - because fans get noisy and it is annoying. But I got this one because the PI was getting too hot.The fan, so far, is amazingly quite and temperature is below 60C which is good. The PI5 has a special connector for the fan which this unit uses.It has pads for all the chips on the board - and it is secured by nylon screws - which ensure firm connection and will not damage the board. Doesn't block access to the camera connectors.Assembly is a bit tricky as you need to select pads by thickness and the difference between 1.5 mm and 2mm is small - but if you place them side by side you can see it - no need to use a caliper.Cons:Instead of using different thickness pads (up to 3mm) they should have machined the heat sink accordingly (some do) and use minimum thickness pads for better heat transfer.
AudioG
2025-06-12 09:37:37
The replacement fan works as expected. The fan on my unit is very quiet (quieter than the RPi Active Cooler, IMO). Running stress tests now, and fully loaded, the cpu temp is holding at 57-60 C. I also have the AI Hat+ installed w/slightly longer standoffs (no physical interference with the cooler), and a taller gpio header. I'm monitoring fan speed w/"watch cat /sys/devices/platform/cooling_fan/hwmon/*/fan1_input" and with the 100% cpu load, the fan speed fluctuates between about 2500 and 4500 rpm. Mostly at 2500 w/short bursts at 4500. Almost inaudible, even at 4500 rpm. So all seems good for now. I'll keep an ear out for fan/bearing noise over time. Held back one star for the hassle of dealing with a DOA.Fan dead right out of the box. Didn't spin at startup init; didn't spin with high temp. I have 8 other RPi5's with a variety of fans, all of which work. Disappointing. Returning for replacement. We'll see how the next one does.
Talistan
2025-06-05 13:33:19
Quiet for the speed it produces and the small bit of noise is not a bad one, smooth sounding, and it fits snug on the pi 5.
Sandra-ann
2025-06-01 12:42:11
Ease of use .
Thouwlin
2025-05-23 11:30:08
I've gotten several of these. The main issue is that you do not know what you are actually going to receive. First order was fine, the second order one was fine 5/16 and the other two were thicker 1/2 to the point that the POE hat with externders would not seat all the way down due to a cap hitting the top of the heat sync. One the other 7 the cap has a good 1/8" clearance.
Jessica Hunt
2025-04-27 17:47:23
Works great to keep my pi 5, which is in a warm electronics bay of my 3d printer, cool and running well. Very quiet, and I confirmed my pi to only run it when needed.
Andre
2025-03-08 13:49:44
Bought 2 heatsink + fan combos for my raspberry pi 5, the heatsink quality and fan size + speed was much more pleasing than any others on offer.
Marc
2025-01-17 17:29:05
je me rend qu’il fonctionne quand je le vois tourner, il ne fait aucun son distinctif.. la température du CPU reste basse, je n’ai pas encore vu plus de 52c après une semaine de mise à jour et d’essai de différents "OS"..
Philip Grant
2024-12-05 18:19:07
Great product that fits and works even better than the original, more expensive OEM cooler.
Ashton
2024-11-24 18:37:20
Cools my Pi 5 sufficiently. Way better than not having a heatsink
Recommended Products