Shopping Cart

Your cart is empty.

Your cart is empty.

GlowShift 44mm 1-3/4' Radiator Hose Attachment Adapter for Water Coolant Temperature Gauge Sensor - Includes Hose Clamps

4.6 (16) Write Review
Free shipping on orders over $29.99

$24.99

$ 10 .99 $10.99

In Stock

About this item

  • GlowShift 44mm (1-3/4") Inner Diameter Hose Attachment Designed for Installing a Water Temperature Sensor Directly to the Coolant Line of the Radiator
  • Features 1/8-27 NPT Thread Port for Temperature Sensor & 2 Hose Clamps to Secure the Adapter to the Coolant Line
  • Manufactured from High-Quality Aluminum that's Built to Last
  • Includes Step-By-Step Installation Instructions
  • GlowShift Guarantee with One Year Limited Warranty & Free Lifetime Technical Support


Product Description

Glowshift's 44mm (1-3/4") Water Sender Adapter is the ideal accessory for anyone looking to install a temperature sensor and gauge to monitor their car or truck’s engine coolant temperature. This water sender hose attachment is designed for compatibility with a radiator hose whose inside diameter is 44mm or 1-3/4”. It also simplifies the installation process by allowing you to easily install your temperature sensor without the need of making any major modifications to your vehicle. Each hose attachment is crafted from aluminum and features a 1/8-27 NPT fitting for your compatible sender. With a few easy steps your sensor will be installed and you’ll be able to take effective water temperature readings.

Water Sender Adapter

When you purchase Glowshift's 44mm (1-3/4") Water Sender Adapter, you’ll also receive (2) hose clamps which secure the line to the water temp sensor hose attachment. These clamps will firmly tighten to the radiator hose, ensuring that the Water Sender Adapter has a leak-tight seal. GlowShift makes the process easy with installation instructions, an installation video, and free lifetime tech support to walk you through the process step-by-step.

As Easy As

Quick Install

With a few simple steps GlowShift’s Water Sender Adapter can be installed along with your water temperature sensor.

1

Cut the Fuel Line

After making sure that the engine is cool, locate a relatively straight section of the coolant hose and make a clean cut through the line.

2

Install the Adapter

Install the clamps over the two cut ends of the hose and place the water temperature sensor adapter in between, securing it tightly into place with the clamps.

3

Install the Sensor

Install the temperature sensor into the adapter, ensuring it is properly tightened. We recommend using Teflon tape on the sensor so that no leaks occur.

About GlowShift

Who We Are

GlowShift is your source for cutting-edge aftermarket automotive products specially designed for cars and trucks. Our diverse lineup includes a variety of gauges, gauge pods, and gauge accessories such as adapters, sensors, wiring harnesses and much more.


Don D.
2025-09-05 10:39:08
I purchased this to be able to install a water temperature sensor for my new electric fan.
Gary Gentry
2025-08-12 17:38:31
Looks amazing and probably would have been great but I had to return due to needing a smaller 38"
Kirvin Tejedor
2025-08-07 14:36:28
Excelente articulo
David w
2025-07-30 16:06:10
Worked as it should. Easy to install good product. Only problem I had was the gauge wasn’t reading correctly. As many know that’s typically a ground problem. Tried taking some Teflon tape off sensor and righting more in a effort to get a ground no luck. When I jumped sensor to a ground it worked so I put a permanent ground from the sensor to the battery and now works fine and is accurate as I checked it with a heat gun. Wasted a lot of time trying to get it to work next time I’m just going to ground it out of the box
Richard
2025-07-14 13:26:57
It is well made quality and priced well. Would suggest in iteme description seller/Amazon specify this is for electric guage installation ONLY as had to have tapped-out to 1/2 NPT as opposed to 1/8 NPT which the came with. Working well so far.
Chas S.
2025-06-11 17:08:46
This is a great product. Unfortunately I order the wrong one. That was on me. But the quality is very high. Definitely recommend
TG72
2025-06-08 12:07:24
Nice adapter, but this one doesn't have a separate ground screw like some others!
Aaron Stice
2025-05-29 15:48:40
Easy to install
Don D.
2025-05-14 11:58:33
I purchased this to be able to install a water temperature sensor for my new electric fan.
Gary Gentry
2025-05-10 21:45:18
Looks amazing and probably would have been great but I had to return due to needing a smaller 38"
Kirvin Tejedor
2025-04-09 16:44:10
Excelente articulo
David w
2025-04-07 15:52:29
Worked as it should. Easy to install good product. Only problem I had was the gauge wasn’t reading correctly. As many know that’s typically a ground problem. Tried taking some Teflon tape off sensor and righting more in a effort to get a ground no luck. When I jumped sensor to a ground it worked so I put a permanent ground from the sensor to the battery and now works fine and is accurate as I checked it with a heat gun. Wasted a lot of time trying to get it to work next time I’m just going to ground it out of the box
Richard
2025-03-26 12:36:02
It is well made quality and priced well. Would suggest in iteme description seller/Amazon specify this is for electric guage installation ONLY as had to have tapped-out to 1/2 NPT as opposed to 1/8 NPT which the came with. Working well so far.
Chas S.
2025-03-04 15:32:05
This is a great product. Unfortunately I order the wrong one. That was on me. But the quality is very high. Definitely recommend
TG72
2025-02-22 10:38:38
Nice adapter, but this one doesn't have a separate ground screw like some others!
Aaron Stice
2025-01-16 18:26:59
Easy to install