Your cart is empty.
Your cart is empty.The integrated design of the ESC and the motor greatly reduces the overall volume and weight, and makes the layout and wiring of car frame simpler and more convenient. The FOC driving mode, low speed torque is strong. Smooth running at extreme low speed, which is far superior to the common sensored brushless power system, even better than the brushed power. Thanks to the sine wave driving mode, the whole system has high efficiency, small heat, and effectively extends the endurance time; and the motor runs more quietly and soft. The protection grade of the whole system is IP67, with excellent waterproof and dustproof performance. Under various weather conditions, the whole system can easily deal with the complex road surface containing silt, ice and snow, and water. Intelligent torque output and speed closed-loop control, fully experience the cruise control and steep slope slow descent function of 1:1 vehicle, making the control handy. Active drag brake force adjustment, providing super strong parking capacity on slope. Multiple protection functions: battery low voltage protection, overheat protection, throttle lost protection, lock-up protection. It supports LED program box to set ESC parameters, and has independent parameter setting interface, which is integrated on electronic switch, making setting parameters more convenient.
Nicolae Mates
2025-09-05 13:25:56
I have 3 or 4 different fusions in my crawlers and I can't have anything else. Especially this SE is a great value, for being a sensored brushless motor, esc, and a built in 4Amp BEC, while being all sealed and waterproof.If this is your first Fusion, or Hobbywing product, know that it doesn't come with a programming card. You will need one to set it up, or borrow from a friend in the hobby. Then just enjoy this very powerfull, smooth and quiet setup. I know I am, and I will be back for more. Quality, performance, direct fit, pwerfull and clean installation with minimal wiring by having built-in ESC and BEC.
Traveler0069
2025-08-28 14:18:49
This motor is so good that it gave my truck enough wheel speed and probably a little bit more than the stock motor and has extreme torque to make your truck climb over stuff, the drag brake is why I purchased this motor and completely satisfied with it, sure the 1800kv motor is probably more ideal for a lot of people but the 1200kv is good enough for what I need and the run time last a little bit longer than the 1800kv but for crawling it's not a race truck so this one is fine, was easy to install, easy to setup and if you have the program card you can find tune it for some stuff just not like the fusion pro 2300kv
Some Dude
2025-08-22 15:21:40
I installed this in my 6lb built crawler and powered it up to rnn it box stock to see if it was enough motor for my gear ratio(13t pinion, 56t spur in an scx10 transmission, injora portal axles, 2.2in. wheels) It's flawless as far as I'm concerned; It's good and slow, it has tons of torque, minimal wires to fight with at installation. I bought a program card, but I doubt I'll need to change many of the stock settings. This is so much easier to set up and run than my brushed setup. I'm a hobbywing fan now.
Jacob Jarosch
2025-08-09 10:44:15
Works perfect in my axial scx103 basecamp and gladiator. Best bang for your buck upgrade in my opion. The slow control compared to a stock motor is night and day difference.
tctech
2025-08-07 15:52:43
Easy to program. So much better than mybrush motor. More control. Being that it has the speed control built-in, allows more room.
Matthew Griffin
2025-07-28 10:29:17
Powerful and quite I love these two and one motor's I use this 1800kv or the pro2300kv in almost all my crawler's.
David
2025-06-17 13:14:35
I have several different Fusion motors and the quality and fitment have always been good. This version is no exception. Lots of torque and quick response make this a good choice. Easy to use right out of the box. Mine needed no programming for use in my robotic project.
Andrew F.
2025-03-09 10:09:56
The media could not be loaded.
JRC father & son hobby
2025-02-28 18:19:13
very quiet motor! l love the way it crawl walk!!! Best for its value. highly recommended!!
Jeffrey Parry
2025-02-20 14:32:34
Just buy it, these things are awesome.Crawling perfection.If you want a bit more speed, grab the 2300kv version.
Buds
2025-01-01 14:43:58
The excellent reviews that it has only begins to explain just how impressive this esc motor combo works. I installed in a trx4. The installation was simple and very neat. I did need to purchase a hobbywing programming card to adjust the motor direction. That also was very easy and explained in the included instructions. It operates almost silently and the slow crawl and smoothness is second to nothing that i have ever tried before..
JimmyC
2024-12-07 11:30:42
First time trying the Fusion SE 1800 and no complaints at all. Very good indeed for the price point and would recommend it all day long if you're looking for a budget brushless motor. Will buy another of these for sure.
Rob
2024-12-03 11:04:09
Got it knowing it was slow and yep it’s slow. Has endless low end power. So hmmm why not see what happens geared up a bit. Wow. Wow. Wow. 24 tooth pinion on a crawler yep. Super slow low end with wheel speed top end. Total game changer. I do own the 2300 pro also that is amazing. This fusion se 1200 is much slower but power to gear up and get that wheel speed. U just don’t know what slow is until you have fusion you also don’t no what torque is until you have a fusion. 36 years experience in the hobby talking here. Just buy it
Recommended Products
$89.99
$ 40 .99 $40.99
$127.33
$ 61 .99 $61.99