Your cart is empty.
Your cart is empty. Features:
Anti flicker resistor decoders are useful for vehicles that get a flickering or strobe effect when installing after market LED bulbs
Resistor & Capacitor built in to solve flickering issues.
This?decoder will work for European vehicles such as Audi, BMW, Mercedes, Porsche
LED Bulbs May Trigger Error Sensors on Some Vehicles with Can-bus Error Detection
LED Decoder, no more OBC warning, fix Hyper Flashing.
Metal Resistor Shell, Male and female connector included
Specification:
T10/194 / W5W LED lights
color: black
material: aluminum cover
voltage: 12 v / 0.29 A
Socket Type: T10/T15 2825, 158, 168, 194, W5W, 912, 921 etc
Package Include:2x T10 LED Wiring Adapter Load Resistor Decoder
Note:
Normally when you flip your turn signal switch, the light blinks at a set, slow pace
If you have modified your lights to use LEDs, you'll notice that the turn signals now blink very quickly (Hyper-Flash). This is caused by the low resistance .
The load resistor on the bypass wiring is?very hot, please mount it to the metal.
PLEASE make sure the power is OFF during installation
Failure due to the different models modified LED lights for different reasons, so we can not figure that all car failure problems can be solved.
Collin
2025-08-26 10:28:19
It works good but beware the socket will not work for all vehicles as the rubber was not wide enough for mine so I had to hardwire it the first time I hardwired it backwards so make sure you have it wired to correct direction, I'm using this for my reverse LED lights because I stayed dimly lit this fixes that issue and I don't have to worry about it getting hot because I'm only using for the reverse lights
Abarth 695
2025-08-17 15:41:00
Bought 6 of these for my night running lights. They worked but then stopped working in 1 minute. Noticed the resistor got hot and the adapter male connector part never made a good connection. I was going to use heat shrink to make sure it stayed on but I think the resistor burnt out so the LED light bulb stopped working. I will have to Sauter and new resistors to see if I can make it work. It’s just disappointing that’s all that it only work for a few minutes. This was being installed in a 2012 Fiat Abarth 500. I will try to make them work or throw them in the garbage.
Mark K
2025-08-10 15:51:44
Of the first set of resistors that arrived, one was defective and didn't work. I was very frustrated because it takes a lot of work to install the parking lights in my car. The company sent a replacement set which arrived a few days later. I installed them and they both worked at first. It was 2 months later I noticed one of the driving lights was out. I checked the connection and the light turned back on. A few weeks after I noticed the light was out again. This time it wouldn't come back on. I bypassed the resistor and the light turned on just fine so the resistor went bad after just 3 months. The company refused to honor a warranty and exchange the resistors after only 3 months.
WG
2025-07-17 17:08:32
Bought these for the extra bright white reverse bulbs on my 2010 Jeep GC.Bulb fit into black end perfectly; white end fit perfectly into stock bulb plug.That said, the black end of this adaptro does not lock into the red turn signal housing. In fact it’s so small that the black junction box, black end and bright led bulb all would have to be inserted into clear taillight Section. Truly takes away from a clean look
Melissa Lira Oehl
2025-07-13 15:10:44
Not sure how good thease are as I never made it past the installation. They look and feel great and are easy to install. However the end that hold the bulb is just a rubber boot. They will not lock into any kind of housing at all. So are useless for me on my 05 Yukon XL.
Angel Narvaez DAD
2025-06-28 21:47:00
Work good!
malik shahid
2025-06-21 15:50:21
worked for me for CT6 back up LED conversion.
Customer
2025-01-18 15:42:34
It didn't last away to the wires come right off.
Recommended Products
