Your cart is empty.
Your cart is empty.Product Description
David Venne
2025-09-01 11:55:31
Both resisters seem well made. The wires are attached soundly with a sleeve over the resister posts. Both measure about 6.6 ohms, which is more than close enough to work in my application where they will be loads for testing 12V batteries.I'm not going to be using the little splicing things, so no comment about them.
Ockham
2025-07-13 15:41:45
These resistors are rated at 50W and are a 6 ohm resistor. Frankly that's a pretty ambitious rating for a resistor of this size, but the do seem to be up to the task.These resistors are intended to be placed in line with the flasher load to simulate the load of the filaments of regular incandescent lamps, causing your LED replacement lamps to flash at the same rate as the OEM tungsten filament lamps.The reason I deducted one star is because the manufacturer supplied blade-lok style crimp connectors to complete the connections.For a load of 50w, these kind of crimp connectors are really just not up to the task. These connections should be crimped with a proper barrel connector - or better yet - soldered and shrink wrapped. Using a cheapo "quickie install shortcut" like the crimp connectors they supplied is a bad precedent. These connector types are not reliable and should not be used in any application where safety in a concern. Properly functioning turn signals is a saftey system issue.Therefore, I dinged one star.Besides that, they look o.k. I recommend that you mount them on a surface in your vehicle that will allow them to dissipate heat - NOT a surface that runs or gets hot.Four stars for the substandard crimps. The resistors look o.k.
Customer
2025-07-09 17:02:15
Previous owner had replaced all the turn signal lamps with LED's, and the flash way too fast. Slowed it down to normal.
Cassandra
2025-07-02 15:27:19
The pair I received measure at 6.2 and 6.3 ohms. Within spec if the tolerance is ±5%. As others have noted they can get rather warm. I suggest you use these for projects that require less than the rated wattage. Note that the listing description recommends mounting them to a metal surface to dissipate heat -- it would be good if a warning was included with the physical product for safety's sake.
Netizen
2025-05-31 17:59:17
Heat up, but in my case, didn't allow high beams or blue indicator light to work when used with Hocolo H4 8000*K bulbs (https://www.amazon.com/dp/B0DJ5W6SJG).
Evangogh
2025-05-19 10:25:19
I'm using these resistors to pre-charge an inverter used with a 12v solar power bank. They're working well and I'm getting no sparks.
Kathy
2025-03-27 17:14:17
I ordered the BFXM 2Pcs 50W 6Ohm Load Resistors because I previously ordered two different brands of LED turn signal bulbs that are advertised as having built-in resistors that prevent fast flashing. Unfortunately, both brands worked at first, but after a couple of months began to give errors and fast flash. The seller recommends that these resistors be mounted to a metal surface because they generate heat, but also states that mounting to metal is not necessary if the bulb is not allowed to flash for more than 20 minutes. My experience indicates that these resistors should be mounted to metal in all cases. I installed one to a rear turn signal, mounted on a metal surface, and let it flash. After about five minutes, the resistor was far too hot to touch; I am sure it would have burned my skin if I had been in contact with it for more than a split second. The metal the resistor is mounted to also was getting hot, although I could still touch it. With that amount of heat in only five minutes, I would not trust these resistors if they were not mounted to a metal heat sink surface. The BFXM 2Pcs 50W 6Ohm Load Resistors do what they are advertised to do, at least initially, but I can only give them four stars because the heat issue is more of a problem than the seller claims.
Roger And Sarah O.
2025-03-10 16:06:47
Installed led lights in my 1979 Corvette and these fixed the blinker issues I was having. Very easy to install didn't use the wire connectors they include not a fan of them being a mechanic for 40 years. But they worked just like they are supposed to.
Francisco Javier
2024-12-20 12:13:22
su instalación es muy fácil y trabaja perfecto solo hay que tener cuidado ya que genera calor
Recommended Products