Your cart is empty.
Your cart is empty.JON EVANS
2025-09-05 18:29:01
Stop hyper flash
Burlie E.
2025-09-01 12:42:44
When I received the resistors I was impressed by the physical appearance of them , they looked very well assembled and are . They go on in a snap and work great . The hardest part was identifying my blinker signal wires which on my Dodge are the outside wires in the socket . I only had the hyper flash when running my lights at night and after installing these babies my blinkers worked like they were supposed to. They look like they are made for the long run and best of all was the price and did I mention I'm a happy camper so buy em , you'll like them . No regrets.
Spaethon
2025-08-19 10:35:43
They were fairly easy to install and worked perfectly. My LED signals all blink at a standard rate. The red clamp completely severed my rear signal ground wire. Maybe a dud, but my car being 23 years old, I definitely didnt want to risk the other wires. I threw the clamps out, wrapped the connections with electrical tape and secured the tape with zip ties. Overall they work perfect and its well worth it. The fast blinking made my car look too jankie.
DB
2025-08-10 13:08:46
I have some LED taillights that I had been running since April suddenly cause hyper blink on my 2007 Jeep Wrangler by July. Tested with my OEM lights to confirm that it was the taillights causing the issue. After researching some videos on YouTube I found that these would possibly solve my problem. I picked up some 1x1 aluminum angle stock at Lowe's as research showed these should not be secured directly to plastic due to how hot they get.There are no directions so do your homework, in my case it was my yellow and black wires that I needed to connect to. I used my T connectors rather than the included ones and there is no positive or negative end to worry about on the resistor. Secured the resistor to the outer end of the bracket with some screws I had around the house, and my handy dandy clear Gorilla glue to secure the bracket to the side of my taillight (I double checked my placement wouldn't interfere prior to gluing it on using a command strip).Not sure about longevity yet as it has only been installed for a week but it fixed my problem, no more hyper flash. Brightness also want an issue so I can't review on that either. I'll double check that my bracket isn't heating up and melting my light in a few days after my road trip which will require brake light usage and update my review if needed.
scott belcourt
2025-07-20 18:37:31
Very easy to install. Instead of using the crimp things which I don’t like in the first place but my LED taillights I purchased for my impala came with resistors the just connect but they didn’t work so I purchased these and it fixed the hyper flash and I soldered them right into the wires from the original resistor wires that I cut off
Customer
2025-06-16 20:36:25
left rear works but the right hand still hyperflashes when turning on turn signal.
Kendroid
2025-06-07 12:16:09
The media could not be loaded.
Professor275
2025-05-11 12:31:26
Installation of led bulbs that tend to hyper-flash defeats entire purpose. Standard long-life bright bulbs last years, are completely bright enough, are reliable. LED headlights are fine, but the turn signal options suck and end up causing too many problems and end up using same energy as regular good bulbs if you need to pair with resistors! Only exception to this problem is if your vehicle has a flasher relay controlling, then you can get a correct relay that will fix, most don't, but check your vehicle and if your lucky this will work and make it useful to use LED turn signal bulbs. The problem with led signal bulbs also includes heat if you need to use resistors with inherent fire danger.
Stephen Morrison
2025-04-17 20:30:37
Ordered these for my Jeep after installing LED turn signals to prevent hyper flash. I’m on my second set after 4 3 years. Make sure to install properly to dissipate heat.
Mario Duquette
2025-03-28 16:42:06
Mes lumières del brûlait sur mon vtt régulièrement mais avec cela sa réglé le problème
Robert Ricard
2025-02-06 18:05:10
after reading reviews about them getting hot, I screwed them away from the important stuff. btw, i didnt get the splice tabs so i improvised.
NIZAROLA
2025-02-05 11:28:54
Needed for LED bulbs on newer vehicles to eliminate bulb error messages
rob w
2025-01-29 11:31:48
**WARNING **These get extremely hot, almost melted the interior cover.Had to remove and buy a proper led light flasher relay instead of using this.
Recommended Products
