Your cart is empty.
Your cart is empty.Product Description
INSTALLATION INSTRUCTIONS
The Malta Dynamics Permanent Roof Anchor has been engineered specifically to be a versatile and durable roof anchor with easy installation. If you’re installing on roofing with asphalt shingles, shakes, or tile, simply remove 1-2 pieces of the roof ridge cap. Then, center the body of the roof anchor on the ridge and position the pre-drilled holes in the middle of the roof framing member. Use screws or the included nails to secure the anchor bracket to the roof. With the unique hole design, no timber splitting should occur. Quick and simple, but for a more detailed installation guide you can consult the product manual.
OSHA/ANSI CERTIFIED
The Malta Dynamics Adjustable Pitch Roof Anchor has been tested to the strict OSHA and ANSI protocols. It meets OSHA 1910, OSHA 1926 Subpart M, ANSI Z359.1-07, and ANSI A10.32-12
LIGHTWEIGHT
With two steel D-Rings - one on each end - this roof anchor offers multiple connection points and sturdy protection. Even with this robust design the whole unit weighs under 1 lb.
EASY INSTALL
This permanent roof anchor is pre-drilled with holes that are designed to minimize damage to trusses and eliminate timber splitting.
LOW PROFILE
The discreet appearance of this 18” steel roof anchor is designed for permanent installation to provide lasting fall protection without compromising the appearance of the roof.
CERTIFICATIONS:
- OSHA 1910, OSHA 1926 Subpart M
- ANSI Z359.1-07, ANSI A10.32-12
FEATURES:
- Worker Capacity Range: 130-310 lbs.
- Body Material: Stainless Steel
- D-Ring Material: Alloy Steel
- Product Weight: 0.9 lbs.
- Product Length: 18”
- Minimum Tensile Breaking Strength: 5,000 lbs.
PREMIUM BENEFITS:
- Easy to Install
- Exclusive Hole Layout Reduces Damage to Truss During Install
- Lightweight and Durable
- Discreet and Low Profile Design
- Reliable D-Ring Anchor Points
- Can be Installed with Screws or Nails
- Fasteners Included (Nails)
Kevin
2025-08-28 20:43:44
After a few near misses on a icy roof, I decided to install permanent anchor points to keep me from going over the edge. There are different systems out there, but I decided on this particular type as I felt it was easier to install on an existing roof . The most difficult part was pealing off the ridge cap to get to the truss.One feature I liked about this particular brand/model was that the D-rings lay flat once installed due to the way the ends are looped around the D-rings. Yet they still have a full range of movement up and down when being used. The band itself appears to be stainless while the D-rings are corrosion resistant metal. Eight nails are included per strap, I elected to use appropriate sized screws instead. The predrilled holes are arranged in a pattern so all of your nails/screws will end up on the truss.Once installed, you can pretty much forget about them, as there is nothing to maintain. And it seems inexpensive versus a trip to the hospital.
RabiysRhyme
2025-08-06 10:36:39
I used this for earthquake restraints on cabinets, cutting each one in half. They looks strong. After the next big one, I will try to remember to update the review...
Customer
2025-06-24 11:48:56
I purchased two of these anchors. The intent was to incorporate them into the roof of my home, which has a steep 12/12 pitch. I used them at the start of my roof replacement with a fall protection harness system. They work great. Unfortunately, they are not long enough to clear the GAF Cobra "Snow Country" rigid venting I chose to use. They had to be removed to finish the roof. They did get used heavily by me for navigating the roof, bearing my weight. I installed them with 9-gauge, 3 inch deck screws, which made for easy removal at the end of laying the shingles.
ran
2025-03-16 17:20:55
If you think your life is worth twenty bucks I recommend this and installing it and then your course getting the safety harness.
R. Sturdivant
2025-03-01 12:50:56
This was a great find for building a shop in my back yard. I was determined to do the roofing myself on my shop, and after a day of being on the roof without a harness and rope, it became apparent to me that I needed some fall protection. This gave me what I needed to be able to attach to the center of the shop roof, and be secure. If you are building larger than a 30-40ft length building, I would recommend getting at least two.
Korbin
2025-02-11 10:28:11
Complete kit nails included. Need to take care nailing as strap is same width as joist and nails holes close to edge. Getting centered on joist tricky.on existing roofing.
Ann Logelin
2025-02-02 18:33:49
They are good.
Printer
2025-01-20 12:35:35
Easy to install, just the right length for under my ridge cap.
Recommended Products