Your cart is empty.
Your cart is empty.Features: 3-way Electronic Crossover 2/4/6 Channel Input 6-Channel / 5 Volt RCA Outputs (Front/Rear/Subwoofer) Front/Rear/Subwoofer Lever Control Subwoofer Equalizer and Boost Level Controls Subwoofer Low-Pass Crossover Control 6/4/2 Channel RCA Inputs 6-Channel / 5 Volt RCA Outputs (Front/Rear/Subwoofer) X20 Frequency Multiplier for Front Channel Low-Pass Crossover 12dB per Octave Crossover Slope Parallel Input Switch, Mixed In/Out Switch Remote Subwoofer Level Control Power on LED Indicator What's in the Box: 3-Way Electronic Crossover 4 Phillips-head Screws Remote Unit Remote Wire 3A Chip Fuse Technical Specs: Hi-Pass Crossover (Front): 35Hz-400Hz Hi-Pass Crossover (Rear): 65Hz-4.5 KHz Low-Pass Crossover (Rear): 300Hz-4.8 KHz Variable Bass Frequency: 40Hz-400Hz Boost Level: 0-18dB Boost Frequency: 40Hz-400Hz Phase Shift: 0 / 180 Subsonic: 25Hz Distortion: 0.05% THD at 1V output level S/N Ratio: 110dB Separation: >60dB Frequency Response: 10 HZ~ 50 KHZ Voltage: 11V-15V Product Dimensions (L x W x H): 10.4'' x 6.3'' x 1.5'' -inches Sold as: 1 Weight: 1.5 lbs.
James Jones
2025-08-20 16:12:42
Output goes from my 6 channel mixer to the Pyle crossover input. The lows go out to my 600 watt 18" bass cabinet, passive input. The highs go to a quality boom box. After dialing in frequencies, amplitudes and channel mixing this little crossover unit is totally awesome and a perfect fit for my small studio. I get those big huge deep bass sounds via the Pyle crossover, send them to my bass cabinet and play the bass guitar in the active input at the same time, no problem and so enjoyable. Note: the manual incorrectly positions the names the Ground, Remote and 12v terminals. I hooked up power according to the labels next to the power terminals and jumped/connected the 12v and Remote terminals together.
E. Heintz
2025-08-13 18:09:42
I bought this for my daughter's Fusion that we installed an aftermarket Android stereo in. It had the Sony Premium Sound in it, and the original head unit did a lot of the signal processing, so it sounded like crap even using the correct PAC adapter to integrate the factory amp.I ran an RCA cable from the new head unit to the input of this crossover. I installed RCA ends on the speaker inputs going to the factory amp and then hooked those to the HPF outputs of the crossover. Her car has factory 6x9 subs, and I ended up powering those with a separate amp (because the factory amp wasn't driving them correctly using the PAC adapter) and ran that signal from the LPF outputs of the crossover.It was some extra effort, but now she has a Tesla-style head unit with Carplay, Navigation, and a backup camera, and it has the awesome Sony sound with even more adjustability.
Tessa S.
2025-08-06 11:36:05
The recommended usage for this active crossover is in a car stereo system, but I added a 12v wall wart and hooked it into a fairly advanced bi-amped home stereo system. It offers a lot of flexibility and works very well. I use it strictly as a low pass filter @ ~ 100hz. It gives me an additional gain control as well as various options for the crossover frequency and slope. It worked perfectly in this application.
Wil2021
2025-07-15 17:22:56
This is a neat device all the way round. The power LED indicator is a handy addition that provides visual feedback on the device's status (no need to guess lol). It allows you to quickly and easily check if the crossover network is functioning properly, saving you time and effort.With the included remote subwoofer control, you have the flexibility to adjust the subwoofer output to suit your preferences. Whether you want to enhance the bass or tone it down, this feature allows you to fine-tune the subwoofer performance without the need to physically interact with the device.
Staceyann
2025-06-28 11:37:46
It value the money love the Quality and it's look very good
E
2025-05-29 10:42:45
Power LED will not light up. Fuse is good.
Ilko
2025-03-27 18:28:13
I recommend. Great crossover.
Nick
2025-03-16 18:33:21
The crossover produced a ton of engine noise, it could be that the ground hook up on this unit is barely 18ga. Or it could be of the cheap components inside, who knows. All I know is, once I disconnected it, and wired my RCA cables directly to the amp, the noise went away???? Minus the engine noise, it did do what it was supposed to do...
Rmo
2025-02-24 10:06:25
Lots of adjustments good with my small mono subwoofer. Much more useful than the smaller Pyle.
Pat Walton
2024-12-27 10:17:50
Works as expected. Used in home stereo rather than car audio.Wired up a 12 volt power adapter with a female to socket with wires out of the back, and jumped the Remote terminal to the positive terminal with a wire so it stays on.Crossover active and functional.
Recommended Products
