Your cart is empty.
Your cart is empty.Product Description
Durable
Made from the premium stainless steel, the hanger is anti-rust, anti-corrosion, durable and not easy to break, can offer long term use.
Adjustable Height
The flex shaft hanger features 3-section steel rod,which can adjust the height from 10-22inch easily
360° rotation
The rotary tidy grinder telescopic hanging tool, designed for flex shaft use, can swivel 360 degrees for easy operation and convenient use
Clamping Direaction
The heavy-duty table-bench clamp can be used vertical or horizontal, Clamp capacity from 0~2-1/2" (0~60mm)
John Pleli
2025-08-26 18:21:12
It was easy to assemble and does what it’s supposed to do. Construction is a little on the light side.
Cassidy Swanson
2025-08-25 12:06:14
I wouldn't put anything heavy on these by any means. I ordered two to hold a shop light above my bench, and it works pretty well for that. But I wouldn't hang an expensive flex shaft from it.
Janis K-C
2025-08-14 15:45:28
Ok i was stupid and bought the cheapest but u get what u pay for. It falls off the desk its clamped to every single time i use it (which honestly has been maybe 15 times since 4/24-otherwise its been hanging there out if the way and not getting touched) the problem is when it starts to get tight enough to not move the metal disk that rests against the desk begins to tilt further and further until it falls off the desk. As you can see it’s completely out of the way.
Bob
2025-08-02 16:55:44
Just what I wanted
Ashlee
2025-06-24 17:44:13
I bought this for my father-in-law to attach to his dialysis cart. I only place 2000 mL bag on it and the plastic part that attaches to the cart just kept bending until it almost breaks. So I just bought another adapter off Amazon and attached the pole to it and it works wonderfully now. Just can’t manage to get the pole to extend all the way up.
pat
2025-06-06 15:28:39
Working great
Don S
2025-05-17 11:50:38
I purchased a set (two) of these hangers and found a couple issues that make it an inferior product. The first is the small hook they placed on the top of the rod to hang the tool from is to wide open so it does not hold the tool in place which results in tool falling off while working. I finally bent mine around a small S-Hook so the tool would stay in place. The second and more significant problem is the cheap plastic they used for a base. When you put the product on a bench the plastic will bend and release the pressure on the clamp which of course causes the stand to fall off. The up right rod is also screwed into this cheap plastic and soon gives out giving you no way to tighten it. So even if they seem cost effective they will not last. I'm currently looking for a better made product with a metal base.
Mike Mathis
2025-04-28 12:57:31
The stand is great if want portability and your rotor motor is light. I like that it breaks down and I can take it to various places. If you are looking for a more permanent place to do your work and your rotary motor is heavy - look for something more fixed and heavy duty.
Charlie
2025-04-11 10:25:25
Merci beaucoup
Terry Muchowski
2025-03-12 13:19:49
it mounts and works pretty good . it is a little flexible compared to the one i already had . it still works .
Caesar
2025-02-14 17:18:18
Threw it out. Waste of time returning this. Too flimsy to hold any a rotary tool, and the clamp is too weak to hold in place.
Russell Pinchbeck
2025-02-03 14:07:40
This product is very light duty. Bracket will likely break and the pole is wobbly. Not impressed.
Nathan
2024-12-27 12:20:20
I don't trust this to hold my flex shaft, even a small one. I've had it fall right off my workbench despite the anchor being secured tightly. The plastic material of the anchor slides easily, even when tightened until the metal side is digging into the wood. Even worse, the pole bends a lot and from just sitting in the cradle for the work day at its shortest and most stable form, it has bent itself to the point that it will no longer stand straight. Overall a complete disappointment.
Recommended Products